--- elwix/config/Attic/ALFA_NX.hints	2013/05/21 08:26:56	1.1
+++ elwix/config/Attic/ALFA_NX.hints	2013/05/21 08:26:57	1.1.2.1
@@ -0,0 +1,149 @@
+# $FreeBSD: src/sys/mips/conf/PB92.hints,v 1.4 2012/11/17 01:52:48 svnexp Exp $
+hint.apb.0.at="nexus0"
+hint.apb.0.irq=4
+
+# uart0
+hint.uart.0.at="apb0"
+# see atheros/uart_cpu_ar71xx.c why +3
+hint.uart.0.maddr=0x18020003
+hint.uart.0.msize=0x18
+hint.uart.0.irq=3
+
+#ehci - note the 0x100 offset for the AR913x/AR724x
+hint.ehci.0.at="nexus0"
+hint.ehci.0.maddr=0x1b000100
+hint.ehci.0.msize=0x00ffff00
+hint.ehci.0.irq=1
+
+# pci
+hint.pcib.0.at="nexus0"
+hint.pcib.0.irq=0
+
+# arge0 MDIO bus
+hint.argemdio.0.at="nexus0"
+hint.argemdio.0.maddr=0x19000000
+hint.argemdio.0.msize=0x1000
+hint.argemdio.0.order=0
+
+# arge0: MII; dedicated PHY 4 on switch, connected via internal switch
+# MDIO bus.
+
+# hint.arge.0.eeprommac=0x83fe9ff0
+hint.arge.0.phymask=0x10	# PHY 4
+# hint.arge.0.miimode=2		# MII
+hint.arge.0.mdio=mdioproxy1	# Hanging off the arswitch MDIO bus
+
+# arge1: connected to the LAN switch MAC, at 1000BaseTX / GMII.
+hint.arge.1.phymask=0x0
+# hint.arge.1.miimode=1		# GMII
+#hint.arge.1.media=1000		# Force to 1000BaseTX/full
+#hint.arge.1.fduplex=1
+
+#
+# AR7240 switch config
+#
+hint.arswitch.0.at="mdio0"
+hint.arswitch.0.is_7240=1	# We need to be explicitly told this
+hint.arswitch.0.numphys=4	# 4 active switch PHYs (PHY 0 -> 3)
+hint.arswitch.0.phy4cpu=1	# Yes, PHY 4 == dedicated PHY
+hint.arswitch.0.is_rgmii=0	# No, not RGMII
+hint.arswitch.0.is_gmii=0	# No, not GMII
+
+## arge0
+#hint.arge.0.at="nexus0"
+#hint.arge.0.maddr=0x19000000
+#hint.arge.0.msize=0x1000
+#hint.arge.0.irq=2
+#
+## AR8316 workaround for now
+#hint.arge.0.media=1000
+#hint.arge.0.fduplex=1
+#hint.arge.0.phymask=0x3
+
+# GPIO
+hint.gpio.0.at="apb0"
+hint.gpio.0.maddr=0x18040000
+hint.gpio.0.msize=0x1000
+hint.gpio.0.irq=2
+
+# Signal leds
+hint.gpioled.0.at="gpiobus0"
+hint.gpioled.0.name="sig1"
+hint.gpioled.0.pins=0x0001	# pin 0
+hint.gpioled.1.at="gpiobus0"
+hint.gpioled.1.name="sig2"
+hint.gpioled.1.pins=0x0002	# pin 1
+hint.gpioled.2.at="gpiobus0"
+hint.gpioled.2.name="sig3"
+hint.gpioled.2.pins=0x0800	# pin 11
+hint.gpioled.3.at="gpiobus0"
+hint.gpioled.3.name="sig4"
+hint.gpioled.3.pins=0x0080	# pin 7
+
+# SPI controller/bus
+hint.spi.0.at="nexus0"
+hint.spi.0.maddr=0x1f000000
+hint.spi.0.msize=0x10
+
+# SPI flash
+hint.mx25l.0.at="spibus0"
+hint.mx25l.0.cs=0
+
+# Watchdog
+hint.ar71xx_wdog.0.at="nexus0"
+
+# nvram mapping - XXX ?
+hint.nvram.0.base=0x1f030000
+hint.nvram.0.maxsize=0x2000
+hint.nvram.0.flags=3 # 1 = No check, 2 = Format Generic
+hint.nvram.1.base=0x1f032000
+hint.nvram.1.maxsize=0x4000
+hint.nvram.1.flags=3 # 1 = No check, 2 = Format Generic
+
+# GEOM_MAP
+#
+# From my PB92 environment:
+#
+# mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),2752k(rootfs),896k(uImage),64k(NVRAM),64k(ART)
+
+hint.map.0.at="flash/spi0"
+hint.map.0.start=0x00000000
+hint.map.0.end=0x00040000	# 256k u-boot
+hint.map.0.name="u-boot"
+hint.map.0.readonly=1
+
+hint.map.1.at="flash/spi0"
+hint.map.1.start=0x00040000
+hint.map.1.end=0x00050000	# 64k u-boot-env
+hint.map.1.name="u-boot-env"
+hint.map.1.readonly=0
+
+hint.map.2.at="flash/spi0"
+hint.map.2.start=0x00050000
+hint.map.2.end=0x00650000	# 6144k rootfs
+hint.map.2.name="rootfs"
+hint.map.2.readonly=0
+
+hint.map.3.at="flash/spi0"
+hint.map.3.start=0x00650000
+hint.map.3.end=0x007e0000	# 1600k uImage
+hint.map.3.name="uImage"
+hint.map.3.readonly=0
+
+hint.map.4.at="flash/spi0"
+hint.map.4.start=0x007e0000
+hint.map.4.end=0x007f0000	# 64k NVRAM
+hint.map.4.name="NVRAM"
+hint.map.4.readonly=0
+
+hint.map.5.at="flash/spi0"
+hint.map.5.start=0x007f0000
+hint.map.5.end=0x00800000	# 64k ART
+hint.map.5.name="ART"
+hint.map.5.readonly=0
+
+hint.map.6.at="flash/spi0"
+hint.map.6.start=0x00050000
+hint.map.6.end=0x007e0000	# 7744k firmware
+hint.map.6.name="firmware"
+hint.map.6.readonly=1