--- elwix/config/Attic/ALFA_NX.hints	2013/05/21 08:26:57	1.1.2.1
+++ elwix/config/Attic/ALFA_NX.hints	2013/05/21 23:48:07	1.1.2.3
@@ -1,4 +1,9 @@
-# $FreeBSD: src/sys/mips/conf/PB92.hints,v 1.4 2012/11/17 01:52:48 svnexp Exp $
+#
+## ELWIX - ALFA Nx kernel hints file
+#
+# $Id: ALFA_NX.hints,v 1.1.2.3 2013/05/21 23:48:07 misho Exp $
+#
+
 hint.apb.0.at="nexus0"
 hint.apb.0.irq=4
 
@@ -9,16 +14,31 @@ hint.uart.0.maddr=0x18020003
 hint.uart.0.msize=0x18
 hint.uart.0.irq=3
 
-#ehci - note the 0x100 offset for the AR913x/AR724x
+#ohci
+hint.ohci.0.at="apb0"
+hint.ohci.0.maddr=0x1c000000
+hint.ohci.0.msize=0x01000000
+hint.ohci.0.irq=6
+
+#ehci
 hint.ehci.0.at="nexus0"
 hint.ehci.0.maddr=0x1b000100
-hint.ehci.0.msize=0x00ffff00
+hint.ehci.0.msize=0x01000000
 hint.ehci.0.irq=1
 
 # pci
 hint.pcib.0.at="nexus0"
 hint.pcib.0.irq=0
 
+# ath0 hint - pcie slot 0
+hint.pcib.0.bus.0.0.0.ath_fixup_addr=0x1fff1000
+hint.pcib.0.bus.0.0.0.ath_fixup_size=4096
+
+# ath
+hint.ath.0.eeprom_firmware="pcib.0.bus.0.0.0.eeprom_firmware"
+# Where the ART is
+hint.ath.0.eepromaddr=0x1fff1000
+
 # arge0 MDIO bus
 hint.argemdio.0.at="nexus0"
 hint.argemdio.0.maddr=0x19000000
@@ -35,6 +55,7 @@ hint.arge.0.mdio=mdioproxy1	# Hanging off the arswitch
 
 # arge1: connected to the LAN switch MAC, at 1000BaseTX / GMII.
 hint.arge.1.phymask=0x0
+hint.arge.1.mdio=mdioproxy1	# Hanging off the arswitch MDIO bus
 # hint.arge.1.miimode=1		# GMII
 #hint.arge.1.media=1000		# Force to 1000BaseTX/full
 #hint.arge.1.fduplex=1
@@ -46,20 +67,21 @@ hint.arswitch.0.at="mdio0"
 hint.arswitch.0.is_7240=1	# We need to be explicitly told this
 hint.arswitch.0.numphys=4	# 4 active switch PHYs (PHY 0 -> 3)
 hint.arswitch.0.phy4cpu=1	# Yes, PHY 4 == dedicated PHY
-hint.arswitch.0.is_rgmii=0	# No, not RGMII
+hint.arswitch.0.is_rgmii=1	# No, not RGMII
 hint.arswitch.0.is_gmii=0	# No, not GMII
 
 ## arge0
-#hint.arge.0.at="nexus0"
-#hint.arge.0.maddr=0x19000000
-#hint.arge.0.msize=0x1000
-#hint.arge.0.irq=2
-#
-## AR8316 workaround for now
-#hint.arge.0.media=1000
-#hint.arge.0.fduplex=1
-#hint.arge.0.phymask=0x3
+hint.arge.0.at="nexus0"
+hint.arge.0.maddr=0x19000000
+hint.arge.0.msize=0x1000
+hint.arge.0.irq=2
 
+
+hint.arge.1.at="nexus0"
+hint.arge.1.maddr=0x1a000000
+hint.arge.1.msize=0x1000
+hint.arge.1.irq=3
+
 # GPIO
 hint.gpio.0.at="apb0"
 hint.gpio.0.maddr=0x18040000
@@ -68,17 +90,26 @@ hint.gpio.0.irq=2
 
 # Signal leds
 hint.gpioled.0.at="gpiobus0"
-hint.gpioled.0.name="sig1"
-hint.gpioled.0.pins=0x0001	# pin 0
+hint.gpioled.0.name="but0"
+hint.gpioled.0.pins=0x00800	# pin 11
 hint.gpioled.1.at="gpiobus0"
 hint.gpioled.1.name="sig2"
-hint.gpioled.1.pins=0x0002	# pin 1
+hint.gpioled.1.pins=0x20000	# pin 17
 hint.gpioled.2.at="gpiobus0"
 hint.gpioled.2.name="sig3"
-hint.gpioled.2.pins=0x0800	# pin 11
-hint.gpioled.3.at="gpiobus0"
-hint.gpioled.3.name="sig4"
-hint.gpioled.3.pins=0x0080	# pin 7
+hint.gpioled.2.pins=0x10000	# pin 16
+hint.gpioled.4.at="gpiobus0"
+hint.gpioled.4.name="sig5"
+hint.gpioled.4.pins=0x01000	# pin 12
+hint.gpioled.5.at="gpiobus0"
+hint.gpioled.5.name="sig6"
+hint.gpioled.5.pins=0x00100	# pin 8
+hint.gpioled.6.at="gpiobus0"
+hint.gpioled.6.name="sig7"
+hint.gpioled.6.pins=0x00040	# pin 6
+hint.gpioled.7.at="gpiobus0"
+hint.gpioled.7.name="sig8"
+hint.gpioled.7.pins=0x00080	# pin 7
 
 # SPI controller/bus
 hint.spi.0.at="nexus0"
@@ -99,6 +130,10 @@ hint.nvram.0.flags=3 # 1 = No check, 2 = Format Generi
 hint.nvram.1.base=0x1f032000
 hint.nvram.1.maxsize=0x4000
 hint.nvram.1.flags=3 # 1 = No check, 2 = Format Generic
+
+# hwpmc device
+hint.ar71xx_pmc.0.at="apb0"
+hint.ar71xx_pmc.0.irq=5
 
 # GEOM_MAP
 #