Return to gettytab CVS log

Up to [ELWIX - Embedded LightWeight unIX -] / elwix / config / etc / default

ELWIX 1.7

    1: # $FreeBSD: src/etc/gettytab,v 1.29 2012/11/17 01:49:01 svnexp Exp $
    2: #	from: @(#)gettytab	5.14 (Berkeley) 3/27/91
    3: #
    4: # Most of the table entries here are just copies of the old getty table,
    5: # it is by no means certain, or even likely, that any of them are optimal
    6: # for any purpose whatever.  Nor is it likely that more than a couple are
    7: # even correct.
    8: #
    9: # The default gettytab entry, used to set defaults for all other
   10: # entries, and in cases where getty is called with no table name.
   11: #
   12: # cb, ce and ck are desirable on most crt's.  The non-crt entries need to
   13: # be changed to turn them off (:cb@:ce@:ck@:).
   14: #
   15: # lc should always be on; it's a remainder of some stone age when there
   16: # have been terminals around not being able of handling lower-case
   17: # characters. Those terminals aren't supported any longer, but getty is
   18: # `smart' about them by default.
   19: #
   20: # Parity defaults to even, but the Pc entry and all the `std' entries
   21: # specify no parity.   The different parities are:
   22: #     (none): same as ep for getty.  login will use terminal as is.
   23: #     ep:     getty will use raw mode (cs8 -parenb) (unless rw is set) and
   24: #             fake parity.  login will use even parity (cs7 parenb -parodd).
   25: #     op:     same as ep except odd parity (cs7 parenb parodd) for login.
   26: #             getty will fake odd parity as well.
   27: #     ap:     same as ep except -inpck instead of inpck for login.
   28: #             ap overrides op and ep.
   29: #     np:     1. don't fake parity in getty.  The fake parity garbles
   30: #                characters on non-terminals (like pccons) that don't
   31: #                support parity.  It would probably better for getty not to
   32: #                try to fake parity.  It could just use cbreak mode so as
   33: #                not to force cs8 and let the hardware handle the parity.
   34: #                login has to be rely on the hardware anyway.
   35: #             2. set cs8 -parenb -istrip -inpck.
   36: #     ep:op:  same as ap.
   37: #
   38: default:\
   39: 	:cb:ce:ck:lc:fd#1000:im=\r\n%s/%m (%h) (%t)\r\n\r\n:sp#1200:\
   40: 	:if=/etc/issue:
   41: 
   42: #
   43: # Fixed speed entries
   44: #
   45: #	The "std.NNN" names are known to the special case
   46: #	portselector code in getty, however they can
   47: #	be assigned to any table desired.
   48: #	The "NNN-baud" names are known to the special case
   49: #	autobaud code in getty, and likewise can
   50: #	be assigned to any table desired (hopefully the same speed).
   51: #
   52: a|std.110|110-baud:\
   53: 	:np:nd#1:cd#1:uc:sp#110:
   54: b|std.134|134.5-baud:\
   55: 	:np:nd#1:cd#2:ff#1:td#1:sp#134:ht:nl:
   56: 1|std.150|150-baud:\
   57: 	:np:nd#1:cd#2:td#1:fd#1:sp#150:ht:nl:lm=\E\72\6\6\17login\72 :
   58: c|std.300|300-baud:\
   59: 	:np:nd#1:cd#1:sp#300:
   60: d|std.600|600-baud:\
   61: 	:np:nd#1:cd#1:sp#600:
   62: f|std.1200|1200-baud:\
   63: 	:np:fd#1:sp#1200:
   64: 6|std.2400|2400-baud:\
   65: 	:np:sp#2400:
   66: 7|std.4800|4800-baud:\
   67: 	:np:sp#4800:
   68: 2|std.9600|9600-baud:\
   69: 	:np:sp#9600:
   70: g|std.19200|19200-baud:\
   71: 	:np:sp#19200:
   72: std.38400|38400-baud:\
   73: 	:np:sp#38400:
   74: std.57600|57600-baud:\
   75: 	:np:sp#57600:
   76: std.115200|115200-baud:\
   77: 	:np:sp#115200:
   78: std.230400|230400-baud:\
   79: 	:np:sp#230400:
   80: 
   81: #
   82: # Entry specifying explicit device settings.  See termios(4) and
   83: # /usr/include/termios.h, too.  The entry forces the tty into
   84: # CLOCAL mode (so no DCD is required), and uses Xon/Xoff flow control.
   85: #
   86: # cflags: CLOCAL | HUPCL | CREAD | CS8
   87: # oflags: OPOST | ONLCR | OXTABS
   88: # iflags: IXOFF | IXON | ICRNL | IGNPAR
   89: # lflags: IEXTEN | ICANON | ISIG | ECHOCTL | ECHO | ECHOK | ECHOE | ECHOKE
   90: #
   91: # The `0' flags don't have input enabled.  The `1' flags don't echo.
   92: # (Echoing is done inside getty itself.)
   93: #
   94: local.9600|CLOCAL tty @ 9600 Bd:\
   95: 	:c0#0x0000c300:c1#0x0000cb00:c2#0x0000cb00:\
   96: 	:o0#0x00000007:o1#0x00000002:o2#0x00000007:\
   97: 	:i0#0x00000704:i1#0x00000000:i2#0x00000704:\
   98: 	:l0#0x000005cf:l1#0x00000000:l2#0x000005cf:\
   99: 	:sp#9600:np:
  100: 
  101: #
  102: # Dial in rotary tables, speed selection via 'break'
  103: #
  104: 0|d300|Dial-300:\
  105: 	:nx=d1200:cd#2:sp#300:
  106: d1200|Dial-1200:\
  107: 	:nx=d150:fd#1:sp#1200:
  108: d150|Dial-150:\
  109: 	:nx=d110:lm@:tc=150-baud:
  110: d110|Dial-110:\
  111: 	:nx=d300:tc=300-baud:
  112: 
  113: #
  114: # Fast dialup terminals, 2400/1200/300 rotary (can start either way)
  115: #
  116: D2400|d2400|Fast-Dial-2400:\
  117: 	:nx=D1200:tc=2400-baud:
  118: 3|D1200|Fast-Dial-1200:\
  119: 	:nx=D300:tc=1200-baud:
  120: 5|D300|Fast-Dial-300:\
  121: 	:nx=D2400:tc=300-baud:
  122: 
  123: #
  124: #telebit (19200)
  125: #
  126: t19200:\
  127: 	:nx=t2400:tc=19200-baud:
  128: t2400:\
  129: 	:nx=t1200:tc=2400-baud:
  130: t1200:\
  131: 	:nx=t19200:tc=1200-baud:
  132: 
  133: #
  134: #telebit (9600)
  135: #
  136: t9600:\
  137: 	:nx=t2400a:tc=9600-baud:
  138: t2400a:\
  139: 	:nx=t1200a:tc=2400-baud:
  140: t1200a:\
  141: 	:nx=t9600:tc=1200-baud:
  142: 
  143: #
  144: # Odd special case terminals
  145: #
  146: -|tty33|asr33|Pity the poor user of this beast:\
  147: 	:tc=110-baud:
  148: 
  149: 4|Console|Console Decwriter II:\
  150: 	:nd@:cd@:rw:tc=300-baud:
  151: 
  152: e|Console-1200|Console Decwriter III:\
  153: 	:fd@:nd@:cd@:rw:tc=1200-baud:
  154: 
  155: i|Interdata console:\
  156: 	:uc:sp#0:
  157: 
  158: l|lsi chess terminal:\
  159: 	:sp#300:
  160: 
  161: X|Xwindow|X window system:\
  162: 	:fd@:nd@:cd@:rw:sp#9600:
  163: 
  164: P|Pc|Pc console:\
  165: 	:ht:np:sp#9600:
  166: 
  167: #
  168: # Weirdo special case for fast crt's with hardcopy devices
  169: #
  170: 8|T9600|CRT with hardcopy:\
  171: 	:nx=T300:tc=9600-baud:
  172: 9|T300|CRT with hardcopy (300):\
  173: 	:nx=T9600:tc=300-baud:
  174: 
  175: #
  176: # Plugboard, and misc other terminals
  177: #
  178: plug-9600|Plugboard-9600:\
  179: 	:pf#1:tc=9600-baud:
  180: p|P9600|Plugboard-9600-rotary:\
  181: 	:pf#1:nx=P300:tc=9600-baud:
  182: q|P300|Plugboard-300:\
  183: 	:pf#1:nx=P1200:tc=300-baud:
  184: r|P1200|Plugboard-1200:\
  185: 	:pf#1:nx=P9600:tc=1200-baud:
  186: 
  187: #
  188: # XXXX Port selector
  189: #
  190: s|DSW|Port Selector:\
  191: 	:ps:sp#2400:
  192: 
  193: #
  194: # Auto-baud speed detect entry for Micom 600.
  195: # Special code in getty will switch this out
  196: # to one of the NNN-baud entries.
  197: #
  198: A|Auto-baud:\
  199: 	:ab:sp#2400:f0#040:
  200: 
  201: #
  202: # autologin - automatically log in as root
  203: #
  204: 
  205: autologin|al.9600:\
  206: 	:al=root:tc=std.9600:
  207: al.19200:\
  208: 	:al=root:tc=std.19200:
  209: al.38400:\
  210: 	:al=root:tc=std.38400:
  211: al.57600:\
  212: 	:al=root:tc=std.57600:
  213: al.115200:\
  214: 	:al=root:tc=std.115200:
  215: al.230400:\
  216: 	:al=root:tc=std.230400:
  217: 
  218: #
  219: # Entries for 3-wire serial terminals.  These don't supply carrier, so
  220: # clocal needs to be set, and crtscts needs to be unset.
  221: #
  222: 3wire.9600|9600-3wire:\
  223: 	:np:nc:sp#9600:
  224: 3wire.19200|19200-3wire:\
  225: 	:np:nc:sp#19200:
  226: 3wire.38400|38400-3wire:\
  227: 	:np:nc:sp#38400:
  228: 3wire.57600|57600-3wire:\
  229: 	:np:nc:sp#57600:
  230: 3wire.115200|115200-3wire:\
  231: 	:np:nc:sp#115200:
  232: 3wire.230400|230400-3wire:\
  233: 	:np:nc:sp#230400: