Annotation of elwix/config/etc/default/hostapd.conf, revision 1.1
1.1 ! misho 1: ##### hostapd configuration file ##############################################
! 2: # Empty lines and lines starting with # are ignored
! 3:
! 4: # AP netdevice name (without 'ap' postfix, i.e., wlan0 uses wlan0ap for
! 5: # management frames); ath0 for madwifi
! 6: interface=wlan0
! 7:
! 8: # In case of madwifi and nl80211 driver interfaces, an additional configuration
! 9: # parameter, bridge, must be used to notify hostapd if the interface is
! 10: # included in a bridge. This parameter is not used with Host AP driver.
! 11: #bridge=br0
! 12:
! 13: # Driver interface type (hostap/wired/madwifi/prism54/test/none/nl80211/bsd);
! 14: # default: hostap). nl80211 is used with all Linux mac80211 drivers.
! 15: # Use driver=none if building hostapd as a standalone RADIUS server that does
! 16: # not control any wireless/wired driver.
! 17: # driver=hostap
! 18:
! 19: # hostapd event logger configuration
! 20: #
! 21: # Two output method: syslog and stdout (only usable if not forking to
! 22: # background).
! 23: #
! 24: # Module bitfield (ORed bitfield of modules that will be logged; -1 = all
! 25: # modules):
! 26: # bit 0 (1) = IEEE 802.11
! 27: # bit 1 (2) = IEEE 802.1X
! 28: # bit 2 (4) = RADIUS
! 29: # bit 3 (8) = WPA
! 30: # bit 4 (16) = driver interface
! 31: # bit 5 (32) = IAPP
! 32: # bit 6 (64) = MLME
! 33: #
! 34: # Levels (minimum value for logged events):
! 35: # 0 = verbose debugging
! 36: # 1 = debugging
! 37: # 2 = informational messages
! 38: # 3 = notification
! 39: # 4 = warning
! 40: #
! 41: logger_syslog=-1
! 42: logger_syslog_level=2
! 43: logger_stdout=-1
! 44: logger_stdout_level=2
! 45:
! 46: # Dump file for state information (on SIGUSR1)
! 47: dump_file=/tmp/hostapd.dump
! 48:
! 49: # Interface for separate control program. If this is specified, hostapd
! 50: # will create this directory and a UNIX domain socket for listening to requests
! 51: # from external programs (CLI/GUI, etc.) for status information and
! 52: # configuration. The socket file will be named based on the interface name, so
! 53: # multiple hostapd processes/interfaces can be run at the same time if more
! 54: # than one interface is used.
! 55: # /var/run/hostapd is the recommended directory for sockets and by default,
! 56: # hostapd_cli will use it when trying to connect with hostapd.
! 57: ctrl_interface=/var/run/hostapd
! 58:
! 59: # Access control for the control interface can be configured by setting the
! 60: # directory to allow only members of a group to use sockets. This way, it is
! 61: # possible to run hostapd as root (since it needs to change network
! 62: # configuration and open raw sockets) and still allow GUI/CLI components to be
! 63: # run as non-root users. However, since the control interface can be used to
! 64: # change the network configuration, this access needs to be protected in many
! 65: # cases. By default, hostapd is configured to use gid 0 (root). If you
! 66: # want to allow non-root users to use the contron interface, add a new group
! 67: # and change this value to match with that group. Add users that should have
! 68: # control interface access to this group.
! 69: #
! 70: # This variable can be a group name or gid.
! 71: #ctrl_interface_group=wheel
! 72: ctrl_interface_group=0
! 73:
! 74:
! 75: ##### IEEE 802.11 related configuration #######################################
! 76:
! 77: # SSID to be used in IEEE 802.11 management frames
! 78: ssid=test
! 79:
! 80: # Country code (ISO/IEC 3166-1). Used to set regulatory domain.
! 81: # Set as needed to indicate country in which device is operating.
! 82: # This can limit available channels and transmit power.
! 83: #country_code=US
! 84:
! 85: # Enable IEEE 802.11d. This advertises the country_code and the set of allowed
! 86: # channels and transmit power levels based on the regulatory limits. The
! 87: # country_code setting must be configured with the correct country for
! 88: # IEEE 802.11d functions.
! 89: # (default: 0 = disabled)
! 90: #ieee80211d=1
! 91:
! 92: # Operation mode (a = IEEE 802.11a, b = IEEE 802.11b, g = IEEE 802.11g,
! 93: # Default: IEEE 802.11b
! 94: hw_mode=a
! 95:
! 96: # Channel number (IEEE 802.11)
! 97: # (default: 0, i.e., not set)
! 98: # Please note that some drivers (e.g., madwifi) do not use this value from
! 99: # hostapd and the channel will need to be configuration separately with
! 100: # iwconfig.
! 101: channel=60
! 102:
! 103: # Beacon interval in kus (1.024 ms) (default: 100; range 15..65535)
! 104: beacon_int=100
! 105:
! 106: # DTIM (delivery trafic information message) period (range 1..255):
! 107: # number of beacons between DTIMs (1 = every beacon includes DTIM element)
! 108: # (default: 2)
! 109: dtim_period=2
! 110:
! 111: # Maximum number of stations allowed in station table. New stations will be
! 112: # rejected after the station table is full. IEEE 802.11 has a limit of 2007
! 113: # different association IDs, so this number should not be larger than that.
! 114: # (default: 2007)
! 115: max_num_sta=255
! 116:
! 117: # RTS/CTS threshold; 2347 = disabled (default); range 0..2347
! 118: # If this field is not included in hostapd.conf, hostapd will not control
! 119: # RTS threshold and 'iwconfig wlan# rts <val>' can be used to set it.
! 120: rts_threshold=2347
! 121:
! 122: # Fragmentation threshold; 2346 = disabled (default); range 256..2346
! 123: # If this field is not included in hostapd.conf, hostapd will not control
! 124: # fragmentation threshold and 'iwconfig wlan# frag <val>' can be used to set
! 125: # it.
! 126: fragm_threshold=2346
! 127:
! 128: # Rate configuration
! 129: # Default is to enable all rates supported by the hardware. This configuration
! 130: # item allows this list be filtered so that only the listed rates will be left
! 131: # in the list. If the list is empty, all rates are used. This list can have
! 132: # entries that are not in the list of rates the hardware supports (such entries
! 133: # are ignored). The entries in this list are in 100 kbps, i.e., 11 Mbps = 110.
! 134: # If this item is present, at least one rate have to be matching with the rates
! 135: # hardware supports.
! 136: # default: use the most common supported rate setting for the selected
! 137: # hw_mode (i.e., this line can be removed from configuration file in most
! 138: # cases)
! 139: #supported_rates=10 20 55 110 60 90 120 180 240 360 480 540
! 140:
! 141: # Basic rate set configuration
! 142: # List of rates (in 100 kbps) that are included in the basic rate set.
! 143: # If this item is not included, usually reasonable default set is used.
! 144: #basic_rates=10 20
! 145: #basic_rates=10 20 55 110
! 146: #basic_rates=60 120 240
! 147:
! 148: # Short Preamble
! 149: # This parameter can be used to enable optional use of short preamble for
! 150: # frames sent at 2 Mbps, 5.5 Mbps, and 11 Mbps to improve network performance.
! 151: # This applies only to IEEE 802.11b-compatible networks and this should only be
! 152: # enabled if the local hardware supports use of short preamble. If any of the
! 153: # associated STAs do not support short preamble, use of short preamble will be
! 154: # disabled (and enabled when such STAs disassociate) dynamically.
! 155: # 0 = do not allow use of short preamble (default)
! 156: # 1 = allow use of short preamble
! 157: #preamble=1
! 158:
! 159: # Station MAC address -based authentication
! 160: # Please note that this kind of access control requires a driver that uses
! 161: # hostapd to take care of management frame processing and as such, this can be
! 162: # used with driver=hostap or driver=nl80211, but not with driver=madwifi.
! 163: # 0 = accept unless in deny list
! 164: # 1 = deny unless in accept list
! 165: # 2 = use external RADIUS server (accept/deny lists are searched first)
! 166: macaddr_acl=0
! 167:
! 168: # Accept/deny lists are read from separate files (containing list of
! 169: # MAC addresses, one per line). Use absolute path name to make sure that the
! 170: # files can be read on SIGHUP configuration reloads.
! 171: #accept_mac_file=/etc/hostapd.accept
! 172: #deny_mac_file=/etc/hostapd.deny
! 173:
! 174: # IEEE 802.11 specifies two authentication algorithms. hostapd can be
! 175: # configured to allow both of these or only one. Open system authentication
! 176: # should be used with IEEE 802.1X.
! 177: # Bit fields of allowed authentication algorithms:
! 178: # bit 0 = Open System Authentication
! 179: # bit 1 = Shared Key Authentication (requires WEP)
! 180: auth_algs=3
! 181:
! 182: # Send empty SSID in beacons and ignore probe request frames that do not
! 183: # specify full SSID, i.e., require stations to know SSID.
! 184: # default: disabled (0)
! 185: # 1 = send empty (length=0) SSID in beacon and ignore probe request for
! 186: # broadcast SSID
! 187: # 2 = clear SSID (ASCII 0), but keep the original length (this may be required
! 188: # with some clients that do not support empty SSID) and ignore probe
! 189: # requests for broadcast SSID
! 190: ignore_broadcast_ssid=0
! 191:
! 192: # TX queue parameters (EDCF / bursting)
! 193: # default for all these fields: not set, use hardware defaults
! 194: # tx_queue_<queue name>_<param>
! 195: # queues: data0, data1, data2, data3, after_beacon, beacon
! 196: # (data0 is the highest priority queue)
! 197: # parameters:
! 198: # aifs: AIFS (default 2)
! 199: # cwmin: cwMin (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023)
! 200: # cwmax: cwMax (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023); cwMax >= cwMin
! 201: # burst: maximum length (in milliseconds with precision of up to 0.1 ms) for
! 202: # bursting
! 203: #
! 204: # Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e):
! 205: # These parameters are used by the access point when transmitting frames
! 206: # to the clients.
! 207: #
! 208: # Low priority / AC_BK = background
! 209: #tx_queue_data3_aifs=7
! 210: #tx_queue_data3_cwmin=15
! 211: #tx_queue_data3_cwmax=1023
! 212: #tx_queue_data3_burst=0
! 213: # Note: for IEEE 802.11b mode: cWmin=31 cWmax=1023 burst=0
! 214: #
! 215: # Normal priority / AC_BE = best effort
! 216: #tx_queue_data2_aifs=3
! 217: #tx_queue_data2_cwmin=15
! 218: #tx_queue_data2_cwmax=63
! 219: #tx_queue_data2_burst=0
! 220: # Note: for IEEE 802.11b mode: cWmin=31 cWmax=127 burst=0
! 221: #
! 222: # High priority / AC_VI = video
! 223: #tx_queue_data1_aifs=1
! 224: #tx_queue_data1_cwmin=7
! 225: #tx_queue_data1_cwmax=15
! 226: #tx_queue_data1_burst=3.0
! 227: # Note: for IEEE 802.11b mode: cWmin=15 cWmax=31 burst=6.0
! 228: #
! 229: # Highest priority / AC_VO = voice
! 230: #tx_queue_data0_aifs=1
! 231: #tx_queue_data0_cwmin=3
! 232: #tx_queue_data0_cwmax=7
! 233: #tx_queue_data0_burst=1.5
! 234: # Note: for IEEE 802.11b mode: cWmin=7 cWmax=15 burst=3.3
! 235: #
! 236: # Special queues; normally not user configurable
! 237: #
! 238: #tx_queue_after_beacon_aifs=2
! 239: #tx_queue_after_beacon_cwmin=15
! 240: #tx_queue_after_beacon_cwmax=1023
! 241: #tx_queue_after_beacon_burst=0
! 242: #
! 243: #tx_queue_beacon_aifs=2
! 244: #tx_queue_beacon_cwmin=3
! 245: #tx_queue_beacon_cwmax=7
! 246: #tx_queue_beacon_burst=1.5
! 247:
! 248: # 802.1D Tag to AC mappings
! 249: # WMM specifies following mapping of data frames to different ACs. This mapping
! 250: # can be configured using Linux QoS/tc and sch_pktpri.o module.
! 251: # 802.1D Tag 802.1D Designation Access Category WMM Designation
! 252: # 1 BK AC_BK Background
! 253: # 2 - AC_BK Background
! 254: # 0 BE AC_BE Best Effort
! 255: # 3 EE AC_VI Video
! 256: # 4 CL AC_VI Video
! 257: # 5 VI AC_VI Video
! 258: # 6 VO AC_VO Voice
! 259: # 7 NC AC_VO Voice
! 260: # Data frames with no priority information: AC_BE
! 261: # Management frames: AC_VO
! 262: # PS-Poll frames: AC_BE
! 263:
! 264: # Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e):
! 265: # for 802.11a or 802.11g networks
! 266: # These parameters are sent to WMM clients when they associate.
! 267: # The parameters will be used by WMM clients for frames transmitted to the
! 268: # access point.
! 269: #
! 270: # note - txop_limit is in units of 32microseconds
! 271: # note - acm is admission control mandatory flag. 0 = admission control not
! 272: # required, 1 = mandatory
! 273: # note - here cwMin and cmMax are in exponent form. the actual cw value used
! 274: # will be (2^n)-1 where n is the value given here
! 275: #
! 276: wme_enabled=1
! 277: #
! 278: # Low priority / AC_BK = background
! 279: wme_ac_bk_cwmin=4
! 280: wme_ac_bk_cwmax=10
! 281: wme_ac_bk_aifs=7
! 282: wme_ac_bk_txop_limit=0
! 283: wme_ac_bk_acm=0
! 284: # Note: for IEEE 802.11b mode: cWmin=5 cWmax=10
! 285: #
! 286: # Normal priority / AC_BE = best effort
! 287: wme_ac_be_aifs=3
! 288: wme_ac_be_cwmin=4
! 289: wme_ac_be_cwmax=10
! 290: wme_ac_be_txop_limit=0
! 291: wme_ac_be_acm=0
! 292: # Note: for IEEE 802.11b mode: cWmin=5 cWmax=7
! 293: #
! 294: # High priority / AC_VI = video
! 295: wme_ac_vi_aifs=2
! 296: wme_ac_vi_cwmin=3
! 297: wme_ac_vi_cwmax=4
! 298: wme_ac_vi_txop_limit=94
! 299: wme_ac_vi_acm=0
! 300: # Note: for IEEE 802.11b mode: cWmin=4 cWmax=5 txop_limit=188
! 301: #
! 302: # Highest priority / AC_VO = voice
! 303: wme_ac_vo_aifs=2
! 304: wme_ac_vo_cwmin=2
! 305: wme_ac_vo_cwmax=3
! 306: wme_ac_vo_txop_limit=47
! 307: wme_ac_vo_acm=0
! 308: # Note: for IEEE 802.11b mode: cWmin=3 cWmax=4 burst=102
! 309:
! 310: # Static WEP key configuration
! 311: #
! 312: # The key number to use when transmitting.
! 313: # It must be between 0 and 3, and the corresponding key must be set.
! 314: # default: not set
! 315: #wep_default_key=0
! 316: # The WEP keys to use.
! 317: # A key may be a quoted string or unquoted hexadecimal digits.
! 318: # The key length should be 5, 13, or 16 characters, or 10, 26, or 32
! 319: # digits, depending on whether 40-bit (64-bit), 104-bit (128-bit), or
! 320: # 128-bit (152-bit) WEP is used.
! 321: # Only the default key must be supplied; the others are optional.
! 322: # default: not set
! 323: #wep_key0=123456789a
! 324: #wep_key1="vwxyz"
! 325: #wep_key2=0102030405060708090a0b0c0d
! 326: #wep_key3=".2.4.6.8.0.23"
! 327:
! 328: # Station inactivity limit
! 329: #
! 330: # If a station does not send anything in ap_max_inactivity seconds, an
! 331: # empty data frame is sent to it in order to verify whether it is
! 332: # still in range. If this frame is not ACKed, the station will be
! 333: # disassociated and then deauthenticated. This feature is used to
! 334: # clear station table of old entries when the STAs move out of the
! 335: # range.
! 336: #
! 337: # The station can associate again with the AP if it is still in range;
! 338: # this inactivity poll is just used as a nicer way of verifying
! 339: # inactivity; i.e., client will not report broken connection because
! 340: # disassociation frame is not sent immediately without first polling
! 341: # the STA with a data frame.
! 342: # default: 300 (i.e., 5 minutes)
! 343: #ap_max_inactivity=300
! 344:
! 345: # Enable/disable internal bridge for packets between associated stations.
! 346: #
! 347: # When IEEE 802.11 is used in managed mode, packets are usually send through
! 348: # the AP even if they are from a wireless station to another wireless station.
! 349: # This functionality requires that the AP has a bridge functionality that sends
! 350: # frames back to the same interface if their destination is another associated
! 351: # station. In addition, broadcast/multicast frames from wireless stations will
! 352: # be sent both to the host system net stack (e.g., to eventually wired network)
! 353: # and back to the wireless interface.
! 354: #
! 355: # The internal bridge is implemented within the wireless kernel module and it
! 356: # bypasses kernel filtering (netfilter/iptables/ebtables). If direct
! 357: # communication between the stations needs to be prevented, the internal
! 358: # bridge can be disabled by setting bridge_packets=0.
! 359: #
! 360: # Note: If this variable is not included in hostapd.conf, hostapd does not
! 361: # change the configuration and iwpriv can be used to set the value with
! 362: # 'iwpriv wlan# param 10 0' command. If the variable is in hostapd.conf,
! 363: # hostapd will override possible iwpriv configuration whenever configuration
! 364: # file is reloaded.
! 365: #
! 366: # default: do not control from hostapd (80211.o defaults to 1=enabled)
! 367: #bridge_packets=1
! 368:
! 369: # Maximum allowed Listen Interval (how many Beacon periods STAs are allowed to
! 370: # remain asleep). Default: 65535 (no limit apart from field size)
! 371: #max_listen_interval=100
! 372:
! 373: ##### IEEE 802.11n related configuration ######################################
! 374:
! 375: # ieee80211n: Whether IEEE 802.11n (HT) is enabled
! 376: # 0 = disabled (default)
! 377: # 1 = enabled
! 378: #ieee80211n=1
! 379:
! 380: # ht_capab: HT capabilities (list of flags)
! 381: # LDPC coding capability: [LDPC] = supported
! 382: # Supported channel width set: [HT40-] = both 20 MHz and 40 MHz with secondary
! 383: # channel below the primary channel; [HT40+] = both 20 MHz and 40 MHz
! 384: # with secondary channel below the primary channel
! 385: # (20 MHz only if neither is set)
! 386: # Note: There are limits on which channels can be used with HT40- and
! 387: # HT40+. Following table shows the channels that may be available for
! 388: # HT40- and HT40+ use per IEEE 802.11n Annex J:
! 389: # freq HT40- HT40+
! 390: # 2.4 GHz 5-13 1-7 (1-9 in Europe/Japan)
! 391: # 5 GHz 40,48,56,64 36,44,52,60
! 392: # (depending on the location, not all of these channels may be available
! 393: # for use)
! 394: # Spatial Multiplexing (SM) Power Save: [SMPS-STATIC] or [SMPS-DYNAMIC]
! 395: # (SMPS disabled if neither is set)
! 396: # HT-greenfield: [GF] (disabled if not set)
! 397: # Short GI for 20 MHz: [SHORT-GI-20] (disabled if not set)
! 398: # Short GI for 40 MHz: [SHORT-GI-40] (disabled if not set)
! 399: # Tx STBC: [TX-STBC] (disabled if not set)
! 400: # Rx STBC: [RX-STBC1] (one spatial stream), [RX-STBC12] (one or two spatial
! 401: # streams), or [RX-STBC123] (one, two, or three spatial streams); Rx STBC
! 402: # disabled if none of these set
! 403: # HT-delayed Block Ack: [DELAYED-BA] (disabled if not set)
! 404: # Maximum A-MSDU length: [MAX-AMSDU-7935] for 7935 octets (3839 octets if not
! 405: # set)
! 406: # DSSS/CCK Mode in 40 MHz: [DSSS_CCK-40] = allowed (not allowed if not set)
! 407: # PSMP support: [PSMP] (disabled if not set)
! 408: # L-SIG TXOP protection support: [LSIG-TXOP-PROT] (disabled if not set)
! 409: #ht_capab=[HT40-][SHORT-GI-20][SHORT-GI-40]
! 410:
! 411: ##### IEEE 802.1X-2004 related configuration ##################################
! 412:
! 413: # Require IEEE 802.1X authorization
! 414: #ieee8021x=1
! 415:
! 416: # IEEE 802.1X/EAPOL version
! 417: # hostapd is implemented based on IEEE Std 802.1X-2004 which defines EAPOL
! 418: # version 2. However, there are many client implementations that do not handle
! 419: # the new version number correctly (they seem to drop the frames completely).
! 420: # In order to make hostapd interoperate with these clients, the version number
! 421: # can be set to the older version (1) with this configuration value.
! 422: #eapol_version=2
! 423:
! 424: # Optional displayable message sent with EAP Request-Identity. The first \0
! 425: # in this string will be converted to ASCII-0 (nul). This can be used to
! 426: # separate network info (comma separated list of attribute=value pairs); see,
! 427: # e.g., RFC 4284.
! 428: #eap_message=hello
! 429: #eap_message=hello\0networkid=netw,nasid=foo,portid=0,NAIRealms=example.com
! 430:
! 431: # WEP rekeying (disabled if key lengths are not set or are set to 0)
! 432: # Key lengths for default/broadcast and individual/unicast keys:
! 433: # 5 = 40-bit WEP (also known as 64-bit WEP with 40 secret bits)
! 434: # 13 = 104-bit WEP (also known as 128-bit WEP with 104 secret bits)
! 435: #wep_key_len_broadcast=5
! 436: #wep_key_len_unicast=5
! 437: # Rekeying period in seconds. 0 = do not rekey (i.e., set keys only once)
! 438: #wep_rekey_period=300
! 439:
! 440: # EAPOL-Key index workaround (set bit7) for WinXP Supplicant (needed only if
! 441: # only broadcast keys are used)
! 442: eapol_key_index_workaround=0
! 443:
! 444: # EAP reauthentication period in seconds (default: 3600 seconds; 0 = disable
! 445: # reauthentication).
! 446: #eap_reauth_period=3600
! 447:
! 448: # Use PAE group address (01:80:c2:00:00:03) instead of individual target
! 449: # address when sending EAPOL frames with driver=wired. This is the most common
! 450: # mechanism used in wired authentication, but it also requires that the port
! 451: # is only used by one station.
! 452: #use_pae_group_addr=1
! 453:
! 454: ##### Integrated EAP server ###################################################
! 455:
! 456: # Optionally, hostapd can be configured to use an integrated EAP server
! 457: # to process EAP authentication locally without need for an external RADIUS
! 458: # server. This functionality can be used both as a local authentication server
! 459: # for IEEE 802.1X/EAPOL and as a RADIUS server for other devices.
! 460:
! 461: # Use integrated EAP server instead of external RADIUS authentication
! 462: # server. This is also needed if hostapd is configured to act as a RADIUS
! 463: # authentication server.
! 464: eap_server=0
! 465:
! 466: # Path for EAP server user database
! 467: #eap_user_file=/etc/hostapd.eap_user
! 468:
! 469: # CA certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS
! 470: #ca_cert=/etc/hostapd.ca.pem
! 471:
! 472: # Server certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS
! 473: #server_cert=/etc/hostapd.server.pem
! 474:
! 475: # Private key matching with the server certificate for EAP-TLS/PEAP/TTLS
! 476: # This may point to the same file as server_cert if both certificate and key
! 477: # are included in a single file. PKCS#12 (PFX) file (.p12/.pfx) can also be
! 478: # used by commenting out server_cert and specifying the PFX file as the
! 479: # private_key.
! 480: #private_key=/etc/hostapd.server.prv
! 481:
! 482: # Passphrase for private key
! 483: #private_key_passwd=secret passphrase
! 484:
! 485: # Enable CRL verification.
! 486: # Note: hostapd does not yet support CRL downloading based on CDP. Thus, a
! 487: # valid CRL signed by the CA is required to be included in the ca_cert file.
! 488: # This can be done by using PEM format for CA certificate and CRL and
! 489: # concatenating these into one file. Whenever CRL changes, hostapd needs to be
! 490: # restarted to take the new CRL into use.
! 491: # 0 = do not verify CRLs (default)
! 492: # 1 = check the CRL of the user certificate
! 493: # 2 = check all CRLs in the certificate path
! 494: #check_crl=1
! 495:
! 496: # dh_file: File path to DH/DSA parameters file (in PEM format)
! 497: # This is an optional configuration file for setting parameters for an
! 498: # ephemeral DH key exchange. In most cases, the default RSA authentication does
! 499: # not use this configuration. However, it is possible setup RSA to use
! 500: # ephemeral DH key exchange. In addition, ciphers with DSA keys always use
! 501: # ephemeral DH keys. This can be used to achieve forward secrecy. If the file
! 502: # is in DSA parameters format, it will be automatically converted into DH
! 503: # params. This parameter is required if anonymous EAP-FAST is used.
! 504: # You can generate DH parameters file with OpenSSL, e.g.,
! 505: # "openssl dhparam -out /etc/hostapd.dh.pem 1024"
! 506: #dh_file=/etc/hostapd.dh.pem
! 507:
! 508: # Configuration data for EAP-SIM database/authentication gateway interface.
! 509: # This is a text string in implementation specific format. The example
! 510: # implementation in eap_sim_db.c uses this as the UNIX domain socket name for
! 511: # the HLR/AuC gateway (e.g., hlr_auc_gw). In this case, the path uses "unix:"
! 512: # prefix.
! 513: #eap_sim_db=unix:/tmp/hlr_auc_gw.sock
! 514:
! 515: # Encryption key for EAP-FAST PAC-Opaque values. This key must be a secret,
! 516: # random value. It is configured as a 16-octet value in hex format. It can be
! 517: # generated, e.g., with the following command:
! 518: # od -tx1 -v -N16 /dev/random | colrm 1 8 | tr -d ' '
! 519: #pac_opaque_encr_key=000102030405060708090a0b0c0d0e0f
! 520:
! 521: # EAP-FAST authority identity (A-ID)
! 522: # A-ID indicates the identity of the authority that issues PACs. The A-ID
! 523: # should be unique across all issuing servers. In theory, this is a variable
! 524: # length field, but due to some existing implementations required A-ID to be
! 525: # 16 octets in length, it is strongly recommended to use that length for the
! 526: # field to provided interoperability with deployed peer implementation. This
! 527: # field is configured in hex format.
! 528: #eap_fast_a_id=101112131415161718191a1b1c1d1e1f
! 529:
! 530: # EAP-FAST authority identifier information (A-ID-Info)
! 531: # This is a user-friendly name for the A-ID. For example, the enterprise name
! 532: # and server name in a human-readable format. This field is encoded as UTF-8.
! 533: #eap_fast_a_id_info=test server
! 534:
! 535: # Enable/disable different EAP-FAST provisioning modes:
! 536: #0 = provisioning disabled
! 537: #1 = only anonymous provisioning allowed
! 538: #2 = only authenticated provisioning allowed
! 539: #3 = both provisioning modes allowed (default)
! 540: #eap_fast_prov=3
! 541:
! 542: # EAP-FAST PAC-Key lifetime in seconds (hard limit)
! 543: #pac_key_lifetime=604800
! 544:
! 545: # EAP-FAST PAC-Key refresh time in seconds (soft limit on remaining hard
! 546: # limit). The server will generate a new PAC-Key when this number of seconds
! 547: # (or fewer) of the lifetime remains.
! 548: #pac_key_refresh_time=86400
! 549:
! 550: # EAP-SIM and EAP-AKA protected success/failure indication using AT_RESULT_IND
! 551: # (default: 0 = disabled).
! 552: #eap_sim_aka_result_ind=1
! 553:
! 554: # Trusted Network Connect (TNC)
! 555: # If enabled, TNC validation will be required before the peer is allowed to
! 556: # connect. Note: This is only used with EAP-TTLS and EAP-FAST. If any other
! 557: # EAP method is enabled, the peer will be allowed to connect without TNC.
! 558: #tnc=1
! 559:
! 560:
! 561: ##### IEEE 802.11f - Inter-Access Point Protocol (IAPP) #######################
! 562:
! 563: # Interface to be used for IAPP broadcast packets
! 564: #iapp_interface=eth0
! 565:
! 566:
! 567: ##### RADIUS client configuration #############################################
! 568: # for IEEE 802.1X with external Authentication Server, IEEE 802.11
! 569: # authentication with external ACL for MAC addresses, and accounting
! 570:
! 571: # The own IP address of the access point (used as NAS-IP-Address)
! 572: own_ip_addr=127.0.0.1
! 573:
! 574: # Optional NAS-Identifier string for RADIUS messages. When used, this should be
! 575: # a unique to the NAS within the scope of the RADIUS server. For example, a
! 576: # fully qualified domain name can be used here.
! 577: # When using IEEE 802.11r, nas_identifier must be set and must be between 1 and
! 578: # 48 octets long.
! 579: #nas_identifier=ap.example.com
! 580:
! 581: # RADIUS authentication server
! 582: #auth_server_addr=127.0.0.1
! 583: #auth_server_port=1812
! 584: #auth_server_shared_secret=secret
! 585:
! 586: # RADIUS accounting server
! 587: #acct_server_addr=127.0.0.1
! 588: #acct_server_port=1813
! 589: #acct_server_shared_secret=secret
! 590:
! 591: # Secondary RADIUS servers; to be used if primary one does not reply to
! 592: # RADIUS packets. These are optional and there can be more than one secondary
! 593: # server listed.
! 594: #auth_server_addr=127.0.0.2
! 595: #auth_server_port=1812
! 596: #auth_server_shared_secret=secret2
! 597: #
! 598: #acct_server_addr=127.0.0.2
! 599: #acct_server_port=1813
! 600: #acct_server_shared_secret=secret2
! 601:
! 602: # Retry interval for trying to return to the primary RADIUS server (in
! 603: # seconds). RADIUS client code will automatically try to use the next server
! 604: # when the current server is not replying to requests. If this interval is set,
! 605: # primary server will be retried after configured amount of time even if the
! 606: # currently used secondary server is still working.
! 607: #radius_retry_primary_interval=600
! 608:
! 609:
! 610: # Interim accounting update interval
! 611: # If this is set (larger than 0) and acct_server is configured, hostapd will
! 612: # send interim accounting updates every N seconds. Note: if set, this overrides
! 613: # possible Acct-Interim-Interval attribute in Access-Accept message. Thus, this
! 614: # value should not be configured in hostapd.conf, if RADIUS server is used to
! 615: # control the interim interval.
! 616: # This value should not be less 600 (10 minutes) and must not be less than
! 617: # 60 (1 minute).
! 618: #radius_acct_interim_interval=600
! 619:
! 620: # Dynamic VLAN mode; allow RADIUS authentication server to decide which VLAN
! 621: # is used for the stations. This information is parsed from following RADIUS
! 622: # attributes based on RFC 3580 and RFC 2868: Tunnel-Type (value 13 = VLAN),
! 623: # Tunnel-Medium-Type (value 6 = IEEE 802), Tunnel-Private-Group-ID (value
! 624: # VLANID as a string). vlan_file option below must be configured if dynamic
! 625: # VLANs are used. Optionally, the local MAC ACL list (accept_mac_file) can be
! 626: # used to set static client MAC address to VLAN ID mapping.
! 627: # 0 = disabled (default)
! 628: # 1 = option; use default interface if RADIUS server does not include VLAN ID
! 629: # 2 = required; reject authentication if RADIUS server does not include VLAN ID
! 630: #dynamic_vlan=0
! 631:
! 632: # VLAN interface list for dynamic VLAN mode is read from a separate text file.
! 633: # This list is used to map VLAN ID from the RADIUS server to a network
! 634: # interface. Each station is bound to one interface in the same way as with
! 635: # multiple BSSIDs or SSIDs. Each line in this text file is defining a new
! 636: # interface and the line must include VLAN ID and interface name separated by
! 637: # white space (space or tab).
! 638: #vlan_file=/etc/hostapd.vlan
! 639:
! 640: # Interface where 802.1q tagged packets should appear when a RADIUS server is
! 641: # used to determine which VLAN a station is on. hostapd creates a bridge for
! 642: # each VLAN. Then hostapd adds a VLAN interface (associated with the interface
! 643: # indicated by 'vlan_tagged_interface') and the appropriate wireless interface
! 644: # to the bridge.
! 645: #vlan_tagged_interface=eth0
! 646:
! 647:
! 648: ##### RADIUS authentication server configuration ##############################
! 649:
! 650: # hostapd can be used as a RADIUS authentication server for other hosts. This
! 651: # requires that the integrated EAP server is also enabled and both
! 652: # authentication services are sharing the same configuration.
! 653:
! 654: # File name of the RADIUS clients configuration for the RADIUS server. If this
! 655: # commented out, RADIUS server is disabled.
! 656: #radius_server_clients=/etc/hostapd.radius_clients
! 657:
! 658: # The UDP port number for the RADIUS authentication server
! 659: #radius_server_auth_port=1812
! 660:
! 661: # Use IPv6 with RADIUS server (IPv4 will also be supported using IPv6 API)
! 662: #radius_server_ipv6=1
! 663:
! 664:
! 665: ##### WPA/IEEE 802.11i configuration ##########################################
! 666:
! 667: # Enable WPA. Setting this variable configures the AP to require WPA (either
! 668: # WPA-PSK or WPA-RADIUS/EAP based on other configuration). For WPA-PSK, either
! 669: # wpa_psk or wpa_passphrase must be set and wpa_key_mgmt must include WPA-PSK.
! 670: # For WPA-RADIUS/EAP, ieee8021x must be set (but without dynamic WEP keys),
! 671: # RADIUS authentication server must be configured, and WPA-EAP must be included
! 672: # in wpa_key_mgmt.
! 673: # This field is a bit field that can be used to enable WPA (IEEE 802.11i/D3.0)
! 674: # and/or WPA2 (full IEEE 802.11i/RSN):
! 675: # bit0 = WPA
! 676: # bit1 = IEEE 802.11i/RSN (WPA2) (dot11RSNAEnabled)
! 677: #wpa=1
! 678:
! 679: # WPA pre-shared keys for WPA-PSK. This can be either entered as a 256-bit
! 680: # secret in hex format (64 hex digits), wpa_psk, or as an ASCII passphrase
! 681: # (8..63 characters) that will be converted to PSK. This conversion uses SSID
! 682: # so the PSK changes when ASCII passphrase is used and the SSID is changed.
! 683: # wpa_psk (dot11RSNAConfigPSKValue)
! 684: # wpa_passphrase (dot11RSNAConfigPSKPassPhrase)
! 685: #wpa_psk=0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef
! 686: #wpa_passphrase=secret passphrase
! 687:
! 688: # Optionally, WPA PSKs can be read from a separate text file (containing list
! 689: # of (PSK,MAC address) pairs. This allows more than one PSK to be configured.
! 690: # Use absolute path name to make sure that the files can be read on SIGHUP
! 691: # configuration reloads.
! 692: #wpa_psk_file=/etc/hostapd.wpa_psk
! 693:
! 694: # Set of accepted key management algorithms (WPA-PSK, WPA-EAP, or both). The
! 695: # entries are separated with a space. WPA-PSK-SHA256 and WPA-EAP-SHA256 can be
! 696: # added to enable SHA256-based stronger algorithms.
! 697: # (dot11RSNAConfigAuthenticationSuitesTable)
! 698: #wpa_key_mgmt=WPA-PSK WPA-EAP
! 699:
! 700: # Set of accepted cipher suites (encryption algorithms) for pairwise keys
! 701: # (unicast packets). This is a space separated list of algorithms:
! 702: # CCMP = AES in Counter mode with CBC-MAC [RFC 3610, IEEE 802.11i/D7.0]
! 703: # TKIP = Temporal Key Integrity Protocol [IEEE 802.11i/D7.0]
! 704: # Group cipher suite (encryption algorithm for broadcast and multicast frames)
! 705: # is automatically selected based on this configuration. If only CCMP is
! 706: # allowed as the pairwise cipher, group cipher will also be CCMP. Otherwise,
! 707: # TKIP will be used as the group cipher.
! 708: # (dot11RSNAConfigPairwiseCiphersTable)
! 709: # Pairwise cipher for WPA (v1) (default: TKIP)
! 710: #wpa_pairwise=TKIP CCMP
! 711: # Pairwise cipher for RSN/WPA2 (default: use wpa_pairwise value)
! 712: #rsn_pairwise=CCMP
! 713:
! 714: # Time interval for rekeying GTK (broadcast/multicast encryption keys) in
! 715: # seconds. (dot11RSNAConfigGroupRekeyTime)
! 716: #wpa_group_rekey=600
! 717:
! 718: # Rekey GTK when any STA that possesses the current GTK is leaving the BSS.
! 719: # (dot11RSNAConfigGroupRekeyStrict)
! 720: #wpa_strict_rekey=1
! 721:
! 722: # Time interval for rekeying GMK (master key used internally to generate GTKs
! 723: # (in seconds).
! 724: #wpa_gmk_rekey=86400
! 725:
! 726: # Maximum lifetime for PTK in seconds. This can be used to enforce rekeying of
! 727: # PTK to mitigate some attacks against TKIP deficiencies.
! 728: #wpa_ptk_rekey=600
! 729:
! 730: # Enable IEEE 802.11i/RSN/WPA2 pre-authentication. This is used to speed up
! 731: # roaming be pre-authenticating IEEE 802.1X/EAP part of the full RSN
! 732: # authentication and key handshake before actually associating with a new AP.
! 733: # (dot11RSNAPreauthenticationEnabled)
! 734: #rsn_preauth=1
! 735: #
! 736: # Space separated list of interfaces from which pre-authentication frames are
! 737: # accepted (e.g., 'eth0' or 'eth0 wlan0wds0'. This list should include all
! 738: # interface that are used for connections to other APs. This could include
! 739: # wired interfaces and WDS links. The normal wireless data interface towards
! 740: # associated stations (e.g., wlan0) should not be added, since
! 741: # pre-authentication is only used with APs other than the currently associated
! 742: # one.
! 743: #rsn_preauth_interfaces=eth0
! 744:
! 745: # peerkey: Whether PeerKey negotiation for direct links (IEEE 802.11e) is
! 746: # allowed. This is only used with RSN/WPA2.
! 747: # 0 = disabled (default)
! 748: # 1 = enabled
! 749: #peerkey=1
! 750:
! 751: # ieee80211w: Whether management frame protection (MFP) is enabled
! 752: # 0 = disabled (default)
! 753: # 1 = optional
! 754: # 2 = required
! 755: #ieee80211w=0
! 756:
! 757: # Association SA Query maximum timeout (in TU = 1.024 ms; for MFP)
! 758: # (maximum time to wait for a SA Query response)
! 759: # dot11AssociationSAQueryMaximumTimeout, 1...4294967295
! 760: #assoc_sa_query_max_timeout=1000
! 761:
! 762: # Association SA Query retry timeout (in TU = 1.024 ms; for MFP)
! 763: # (time between two subsequent SA Query requests)
! 764: # dot11AssociationSAQueryRetryTimeout, 1...4294967295
! 765: #assoc_sa_query_retry_timeout=201
! 766:
! 767:
! 768: # okc: Opportunistic Key Caching (aka Proactive Key Caching)
! 769: # Allow PMK cache to be shared opportunistically among configured interfaces
! 770: # and BSSes (i.e., all configurations within a single hostapd process).
! 771: # 0 = disabled (default)
! 772: # 1 = enabled
! 773: #okc=1
! 774:
! 775:
! 776: ##### IEEE 802.11r configuration ##############################################
! 777:
! 778: # Mobility Domain identifier (dot11FTMobilityDomainID, MDID)
! 779: # MDID is used to indicate a group of APs (within an ESS, i.e., sharing the
! 780: # same SSID) between which a STA can use Fast BSS Transition.
! 781: # 2-octet identifier as a hex string.
! 782: #mobility_domain=a1b2
! 783:
! 784: # PMK-R0 Key Holder identifier (dot11FTR0KeyHolderID)
! 785: # 1 to 48 octet identifier.
! 786: # This is configured with nas_identifier (see RADIUS client section above).
! 787:
! 788: # Default lifetime of the PMK-RO in minutes; range 1..65535
! 789: # (dot11FTR0KeyLifetime)
! 790: #r0_key_lifetime=10000
! 791:
! 792: # PMK-R1 Key Holder identifier (dot11FTR1KeyHolderID)
! 793: # 6-octet identifier as a hex string.
! 794: #r1_key_holder=000102030405
! 795:
! 796: # Reassociation deadline in time units (TUs / 1.024 ms; range 1000..65535)
! 797: # (dot11FTReassociationDeadline)
! 798: #reassociation_deadline=1000
! 799:
! 800: # List of R0KHs in the same Mobility Domain
! 801: # format: <MAC address> <NAS Identifier> <128-bit key as hex string>
! 802: # This list is used to map R0KH-ID (NAS Identifier) to a destination MAC
! 803: # address when requesting PMK-R1 key from the R0KH that the STA used during the
! 804: # Initial Mobility Domain Association.
! 805: #r0kh=02:01:02:03:04:05 r0kh-1.example.com 000102030405060708090a0b0c0d0e0f
! 806: #r0kh=02:01:02:03:04:06 r0kh-2.example.com 00112233445566778899aabbccddeeff
! 807: # And so on.. One line per R0KH.
! 808:
! 809: # List of R1KHs in the same Mobility Domain
! 810: # format: <MAC address> <R0KH-ID> <128-bit key as hex string>
! 811: # This list is used to map R1KH-ID to a destination MAC address when sending
! 812: # PMK-R1 key from the R0KH. This is also the list of authorized R1KHs in the MD
! 813: # that can request PMK-R1 keys.
! 814: #r1kh=02:01:02:03:04:05 02:11:22:33:44:55 000102030405060708090a0b0c0d0e0f
! 815: #r1kh=02:01:02:03:04:06 02:11:22:33:44:66 00112233445566778899aabbccddeeff
! 816: # And so on.. One line per R1KH.
! 817:
! 818: # Whether PMK-R1 push is enabled at R0KH
! 819: # 0 = do not push PMK-R1 to all configured R1KHs (default)
! 820: # 1 = push PMK-R1 to all configured R1KHs whenever a new PMK-R0 is derived
! 821: #pmk_r1_push=1
! 822:
! 823: ##### Passive scanning ########################################################
! 824: # Scan different channels every N seconds. 0 = disable passive scanning.
! 825: #passive_scan_interval=60
! 826:
! 827: # Listen N usecs on each channel when doing passive scanning.
! 828: # This value plus the time needed for changing channels should be less than
! 829: # 32 milliseconds (i.e. 32000 usec) to avoid interruptions to normal
! 830: # operations. Time needed for channel changing varies based on the used wlan
! 831: # hardware.
! 832: # default: disabled (0)
! 833: #passive_scan_listen=10000
! 834:
! 835: # Passive scanning mode:
! 836: # 0 = scan all supported modes (802.11a/b/g/Turbo) (default)
! 837: # 1 = scan only the mode that is currently used for normal operations
! 838: #passive_scan_mode=1
! 839:
! 840: # Maximum number of entries kept in AP table (either for passive scanning or
! 841: # for detecting Overlapping Legacy BSS Condition). The oldest entry will be
! 842: # removed when adding a new entry that would make the list grow over this
! 843: # limit. Note! Wi-Fi certification for IEEE 802.11g requires that OLBC is
! 844: # enabled, so this field should not be set to 0 when using IEEE 802.11g.
! 845: # default: 255
! 846: #ap_table_max_size=255
! 847:
! 848: # Number of seconds of no frames received after which entries may be deleted
! 849: # from the AP table. Since passive scanning is not usually performed frequently
! 850: # this should not be set to very small value. In addition, there is no
! 851: # guarantee that every scan cycle will receive beacon frames from the
! 852: # neighboring APs.
! 853: # default: 60
! 854: #ap_table_expiration_time=3600
! 855:
! 856:
! 857: ##### Wi-Fi Protected Setup (WPS) #############################################
! 858:
! 859: # WPS state
! 860: # 0 = WPS disabled (default)
! 861: # 1 = WPS enabled, not configured
! 862: # 2 = WPS enabled, configured
! 863: #wps_state=2
! 864:
! 865: # AP can be configured into a locked state where new WPS Registrar are not
! 866: # accepted, but previously authorized Registrars (including the internal one)
! 867: # can continue to add new Enrollees.
! 868: #ap_setup_locked=1
! 869:
! 870: # Universally Unique IDentifier (UUID; see RFC 4122) of the device
! 871: # This value is used as the UUID for the internal WPS Registrar. If the AP
! 872: # is also using UPnP, this value should be set to the device's UPnP UUID.
! 873: # If not configured, UUID will be generated based on the local MAC address.
! 874: #uuid=12345678-9abc-def0-1234-56789abcdef0
! 875:
! 876: # Note: If wpa_psk_file is set, WPS is used to generate random, per-device PSKs
! 877: # that will be appended to the wpa_psk_file. If wpa_psk_file is not set, the
! 878: # default PSK (wpa_psk/wpa_passphrase) will be delivered to Enrollees. Use of
! 879: # per-device PSKs is recommended as the more secure option (i.e., make sure to
! 880: # set wpa_psk_file when using WPS with WPA-PSK).
! 881:
! 882: # When an Enrollee requests access to the network with PIN method, the Enrollee
! 883: # PIN will need to be entered for the Registrar. PIN request notifications are
! 884: # sent to hostapd ctrl_iface monitor. In addition, they can be written to a
! 885: # text file that could be used, e.g., to populate the AP administration UI with
! 886: # pending PIN requests. If the following variable is set, the PIN requests will
! 887: # be written to the configured file.
! 888: #wps_pin_requests=/var/run/hostapd_wps_pin_requests
! 889:
! 890: # Device Name
! 891: # User-friendly description of device; up to 32 octets encoded in UTF-8
! 892: #device_name=Wireless AP
! 893:
! 894: # Manufacturer
! 895: # The manufacturer of the device (up to 64 ASCII characters)
! 896: #manufacturer=Company
! 897:
! 898: # Model Name
! 899: # Model of the device (up to 32 ASCII characters)
! 900: #model_name=WAP
! 901:
! 902: # Model Number
! 903: # Additional device description (up to 32 ASCII characters)
! 904: #model_number=123
! 905:
! 906: # Serial Number
! 907: # Serial number of the device (up to 32 characters)
! 908: #serial_number=12345
! 909:
! 910: # Primary Device Type
! 911: # Used format: <categ>-<OUI>-<subcateg>
! 912: # categ = Category as an integer value
! 913: # OUI = OUI and type octet as a 4-octet hex-encoded value; 0050F204 for
! 914: # default WPS OUI
! 915: # subcateg = OUI-specific Sub Category as an integer value
! 916: # Examples:
! 917: # 1-0050F204-1 (Computer / PC)
! 918: # 1-0050F204-2 (Computer / Server)
! 919: # 5-0050F204-1 (Storage / NAS)
! 920: # 6-0050F204-1 (Network Infrastructure / AP)
! 921: #device_type=6-0050F204-1
! 922:
! 923: # OS Version
! 924: # 4-octet operating system version number (hex string)
! 925: #os_version=01020300
! 926:
! 927: # Config Methods
! 928: # List of the supported configuration methods
! 929: #config_methods=label display push_button keypad
! 930:
! 931: # Access point PIN for initial configuration and adding Registrars
! 932: # If not set, hostapd will not allow external WPS Registrars to control the
! 933: # access point.
! 934: #ap_pin=12345670
! 935:
! 936: # Skip building of automatic WPS credential
! 937: # This can be used to allow the automatically generated Credential attribute to
! 938: # be replaced with pre-configured Credential(s).
! 939: #skip_cred_build=1
! 940:
! 941: # Additional Credential attribute(s)
! 942: # This option can be used to add pre-configured Credential attributes into M8
! 943: # message when acting as a Registrar. If skip_cred_build=1, this data will also
! 944: # be able to override the Credential attribute that would have otherwise been
! 945: # automatically generated based on network configuration. This configuration
! 946: # option points to an external file that much contain the WPS Credential
! 947: # attribute(s) as binary data.
! 948: #extra_cred=hostapd.cred
! 949:
! 950: # Credential processing
! 951: # 0 = process received credentials internally (default)
! 952: # 1 = do not process received credentials; just pass them over ctrl_iface to
! 953: # external program(s)
! 954: # 2 = process received credentials internally and pass them over ctrl_iface
! 955: # to external program(s)
! 956: # Note: With wps_cred_processing=1, skip_cred_build should be set to 1 and
! 957: # extra_cred be used to provide the Credential data for Enrollees.
! 958: #
! 959: # wps_cred_processing=1 will disabled automatic updates of hostapd.conf file
! 960: # both for Credential processing and for marking AP Setup Locked based on
! 961: # validation failures of AP PIN. An external program is responsible on updating
! 962: # the configuration appropriately in this case.
! 963: #wps_cred_processing=0
! 964:
! 965: # AP Settings Attributes for M7
! 966: # By default, hostapd generates the AP Settings Attributes for M7 based on the
! 967: # current configuration. It is possible to override this by providing a file
! 968: # with pre-configured attributes. This is similar to extra_cred file format,
! 969: # but the AP Settings attributes are not encapsulated in a Credential
! 970: # attribute.
! 971: #ap_settings=hostapd.ap_settings
! 972:
! 973: # WPS UPnP interface
! 974: # If set, support for external Registrars is enabled.
! 975: #upnp_iface=br0
! 976:
! 977: # Friendly Name (required for UPnP)
! 978: # Short description for end use. Should be less than 64 characters.
! 979: #friendly_name=WPS Access Point
! 980:
! 981: # Manufacturer URL (optional for UPnP)
! 982: #manufacturer_url=http://www.example.com/
! 983:
! 984: # Model Description (recommended for UPnP)
! 985: # Long description for end user. Should be less than 128 characters.
! 986: #model_description=Wireless Access Point
! 987:
! 988: # Model URL (optional for UPnP)
! 989: #model_url=http://www.example.com/model/
! 990:
! 991: # Universal Product Code (optional for UPnP)
! 992: # 12-digit, all-numeric code that identifies the consumer package.
! 993: #upc=123456789012
! 994:
! 995: ##### Multiple BSSID support ##################################################
! 996: #
! 997: # Above configuration is using the default interface (wlan#, or multi-SSID VLAN
! 998: # interfaces). Other BSSIDs can be added by using separator 'bss' with
! 999: # default interface name to be allocated for the data packets of the new BSS.
! 1000: #
! 1001: # hostapd will generate BSSID mask based on the BSSIDs that are
! 1002: # configured. hostapd will verify that dev_addr & MASK == dev_addr. If this is
! 1003: # not the case, the MAC address of the radio must be changed before starting
! 1004: # hostapd (ifconfig wlan0 hw ether <MAC addr>).
! 1005: #
! 1006: # BSSIDs are assigned in order to each BSS, unless an explicit BSSID is
! 1007: # specified using the 'bssid' parameter.
! 1008: # If an explicit BSSID is specified, it must be chosen such that it:
! 1009: # - results in a valid MASK that covers it and the dev_addr
! 1010: # - is not the same as the MAC address of the radio
! 1011: # - is not the same as any other explicitly specified BSSID
! 1012: #
! 1013: # Please note that hostapd uses some of the values configured for the first BSS
! 1014: # as the defaults for the following BSSes. However, it is recommended that all
! 1015: # BSSes include explicit configuration of all relevant configuration items.
! 1016: #
! 1017: #bss=wlan0_0
! 1018: #ssid=test2
! 1019: # most of the above items can be used here (apart from radio interface specific
! 1020: # items, like channel)
! 1021:
! 1022: #bss=wlan0_1
! 1023: #bssid=00:13:10:95:fe:0b
! 1024: # ...
FreeBSD-CVSweb <freebsd-cvsweb@FreeBSD.org>
![[BACK]](/icons/cvsweb/back.gif){kind=icon}
Return to hostapd.conf CVS log ![[TXT]](/icons/cvsweb/text.gif){kind=icon}
![[DIR]](/icons/cvsweb/dir.gif){kind=icon}
Up to [ELWIX - Embedded LightWeight unIX -] / elwix / config / etc / default