Annotation of elwix/config/etc/uboot/gettytab, revision 1.1.2.1
1.1.2.1 ! misho 1: # $FreeBSD: src/etc/gettytab,v 1.29 2012/11/17 01:49:01 svnexp Exp $
! 2: # from: @(#)gettytab 5.14 (Berkeley) 3/27/91
! 3: #
! 4: # Most of the table entries here are just copies of the old getty table,
! 5: # it is by no means certain, or even likely, that any of them are optimal
! 6: # for any purpose whatever. Nor is it likely that more than a couple are
! 7: # even correct.
! 8: #
! 9: # The default gettytab entry, used to set defaults for all other
! 10: # entries, and in cases where getty is called with no table name.
! 11: #
! 12: # cb, ce and ck are desirable on most crt's. The non-crt entries need to
! 13: # be changed to turn them off (:cb@:ce@:ck@:).
! 14: #
! 15: # lc should always be on; it's a remainder of some stone age when there
! 16: # have been terminals around not being able of handling lower-case
! 17: # characters. Those terminals aren't supported any longer, but getty is
! 18: # `smart' about them by default.
! 19: #
! 20: # Parity defaults to even, but the Pc entry and all the `std' entries
! 21: # specify no parity. The different parities are:
! 22: # (none): same as ep for getty. login will use terminal as is.
! 23: # ep: getty will use raw mode (cs8 -parenb) (unless rw is set) and
! 24: # fake parity. login will use even parity (cs7 parenb -parodd).
! 25: # op: same as ep except odd parity (cs7 parenb parodd) for login.
! 26: # getty will fake odd parity as well.
! 27: # ap: same as ep except -inpck instead of inpck for login.
! 28: # ap overrides op and ep.
! 29: # np: 1. don't fake parity in getty. The fake parity garbles
! 30: # characters on non-terminals (like pccons) that don't
! 31: # support parity. It would probably better for getty not to
! 32: # try to fake parity. It could just use cbreak mode so as
! 33: # not to force cs8 and let the hardware handle the parity.
! 34: # login has to be rely on the hardware anyway.
! 35: # 2. set cs8 -parenb -istrip -inpck.
! 36: # ep:op: same as ap.
! 37: #
! 38: default:\
! 39: :cb:ce:ck:lc:fd#1000:im=\r\n%s/%m (%h) (%t)\r\n\r\n:sp#1200:\
! 40: :if=/etc/issue:
! 41:
! 42: #
! 43: # Fixed speed entries
! 44: #
! 45: # The "std.NNN" names are known to the special case
! 46: # portselector code in getty, however they can
! 47: # be assigned to any table desired.
! 48: # The "NNN-baud" names are known to the special case
! 49: # autobaud code in getty, and likewise can
! 50: # be assigned to any table desired (hopefully the same speed).
! 51: #
! 52: a|std.110|110-baud:\
! 53: :np:nd#1:cd#1:uc:sp#110:
! 54: b|std.134|134.5-baud:\
! 55: :np:nd#1:cd#2:ff#1:td#1:sp#134:ht:nl:
! 56: 1|std.150|150-baud:\
! 57: :np:nd#1:cd#2:td#1:fd#1:sp#150:ht:nl:lm=\E\72\6\6\17login\72 :
! 58: c|std.300|300-baud:\
! 59: :np:nd#1:cd#1:sp#300:
! 60: d|std.600|600-baud:\
! 61: :np:nd#1:cd#1:sp#600:
! 62: f|std.1200|1200-baud:\
! 63: :np:fd#1:sp#1200:
! 64: 6|std.2400|2400-baud:\
! 65: :np:sp#2400:
! 66: 7|std.4800|4800-baud:\
! 67: :np:sp#4800:
! 68: 2|std.9600|9600-baud:\
! 69: :np:sp#9600:
! 70: g|std.19200|19200-baud:\
! 71: :np:sp#19200:
! 72: std.38400|38400-baud:\
! 73: :np:sp#38400:
! 74: std.57600|57600-baud:\
! 75: :np:sp#57600:
! 76: std.115200|115200-baud:\
! 77: :np:sp#115200:
! 78: std.230400|230400-baud:\
! 79: :np:sp#230400:
! 80:
! 81: #
! 82: # Entry specifying explicit device settings. See termios(4) and
! 83: # /usr/include/termios.h, too. The entry forces the tty into
! 84: # CLOCAL mode (so no DCD is required), and uses Xon/Xoff flow control.
! 85: #
! 86: # cflags: CLOCAL | HUPCL | CREAD | CS8
! 87: # oflags: OPOST | ONLCR | OXTABS
! 88: # iflags: IXOFF | IXON | ICRNL | IGNPAR
! 89: # lflags: IEXTEN | ICANON | ISIG | ECHOCTL | ECHO | ECHOK | ECHOE | ECHOKE
! 90: #
! 91: # The `0' flags don't have input enabled. The `1' flags don't echo.
! 92: # (Echoing is done inside getty itself.)
! 93: #
! 94: local.9600|CLOCAL tty @ 9600 Bd:\
! 95: :c0#0x0000c300:c1#0x0000cb00:c2#0x0000cb00:\
! 96: :o0#0x00000007:o1#0x00000002:o2#0x00000007:\
! 97: :i0#0x00000704:i1#0x00000000:i2#0x00000704:\
! 98: :l0#0x000005cf:l1#0x00000000:l2#0x000005cf:\
! 99: :sp#9600:np:
! 100:
! 101: #
! 102: # Dial in rotary tables, speed selection via 'break'
! 103: #
! 104: 0|d300|Dial-300:\
! 105: :nx=d1200:cd#2:sp#300:
! 106: d1200|Dial-1200:\
! 107: :nx=d150:fd#1:sp#1200:
! 108: d150|Dial-150:\
! 109: :nx=d110:lm@:tc=150-baud:
! 110: d110|Dial-110:\
! 111: :nx=d300:tc=300-baud:
! 112:
! 113: #
! 114: # Fast dialup terminals, 2400/1200/300 rotary (can start either way)
! 115: #
! 116: D2400|d2400|Fast-Dial-2400:\
! 117: :nx=D1200:tc=2400-baud:
! 118: 3|D1200|Fast-Dial-1200:\
! 119: :nx=D300:tc=1200-baud:
! 120: 5|D300|Fast-Dial-300:\
! 121: :nx=D2400:tc=300-baud:
! 122:
! 123: #
! 124: #telebit (19200)
! 125: #
! 126: t19200:\
! 127: :nx=t2400:tc=19200-baud:
! 128: t2400:\
! 129: :nx=t1200:tc=2400-baud:
! 130: t1200:\
! 131: :nx=t19200:tc=1200-baud:
! 132:
! 133: #
! 134: #telebit (9600)
! 135: #
! 136: t9600:\
! 137: :nx=t2400a:tc=9600-baud:
! 138: t2400a:\
! 139: :nx=t1200a:tc=2400-baud:
! 140: t1200a:\
! 141: :nx=t9600:tc=1200-baud:
! 142:
! 143: #
! 144: # Odd special case terminals
! 145: #
! 146: -|tty33|asr33|Pity the poor user of this beast:\
! 147: :tc=110-baud:
! 148:
! 149: 4|Console|Console Decwriter II:\
! 150: :nd@:cd@:rw:tc=300-baud:
! 151:
! 152: e|Console-1200|Console Decwriter III:\
! 153: :fd@:nd@:cd@:rw:tc=1200-baud:
! 154:
! 155: i|Interdata console:\
! 156: :uc:sp#0:
! 157:
! 158: l|lsi chess terminal:\
! 159: :sp#300:
! 160:
! 161: X|Xwindow|X window system:\
! 162: :fd@:nd@:cd@:rw:sp#9600:
! 163:
! 164: P|Pc|Pc console:\
! 165: :ht:np:sp#9600:
! 166:
! 167: #
! 168: # Weirdo special case for fast crt's with hardcopy devices
! 169: #
! 170: 8|T9600|CRT with hardcopy:\
! 171: :nx=T300:tc=9600-baud:
! 172: 9|T300|CRT with hardcopy (300):\
! 173: :nx=T9600:tc=300-baud:
! 174:
! 175: #
! 176: # Plugboard, and misc other terminals
! 177: #
! 178: plug-9600|Plugboard-9600:\
! 179: :pf#1:tc=9600-baud:
! 180: p|P9600|Plugboard-9600-rotary:\
! 181: :pf#1:nx=P300:tc=9600-baud:
! 182: q|P300|Plugboard-300:\
! 183: :pf#1:nx=P1200:tc=300-baud:
! 184: r|P1200|Plugboard-1200:\
! 185: :pf#1:nx=P9600:tc=1200-baud:
! 186:
! 187: #
! 188: # XXXX Port selector
! 189: #
! 190: s|DSW|Port Selector:\
! 191: :ps:sp#2400:
! 192:
! 193: #
! 194: # Auto-baud speed detect entry for Micom 600.
! 195: # Special code in getty will switch this out
! 196: # to one of the NNN-baud entries.
! 197: #
! 198: A|Auto-baud:\
! 199: :ab:sp#2400:f0#040:
! 200:
! 201: #
! 202: # autologin - automatically log in as root
! 203: #
! 204:
! 205: autologin|al.9600:\
! 206: :al=root:tc=std.9600:
! 207: al.19200:\
! 208: :al=root:tc=std.19200:
! 209: al.38400:\
! 210: :al=root:tc=std.38400:
! 211: al.57600:\
! 212: :al=root:tc=std.57600:
! 213: al.115200:\
! 214: :al=root:tc=std.115200:
! 215: al.230400:\
! 216: :al=root:tc=std.230400:
! 217:
! 218: #
! 219: # Entries for 3-wire serial terminals. These don't supply carrier, so
! 220: # clocal needs to be set, and crtscts needs to be unset.
! 221: #
! 222: 3wire.9600|9600-3wire:\
! 223: :np:nc:sp#9600:
! 224: 3wire.19200|19200-3wire:\
! 225: :np:nc:sp#19200:
! 226: 3wire.38400|38400-3wire:\
! 227: :np:nc:sp#38400:
! 228: 3wire.57600|57600-3wire:\
! 229: :np:nc:sp#57600:
! 230: 3wire.115200|115200-3wire:\
! 231: :np:nc:sp#115200:
! 232: 3wire.230400|230400-3wire:\
! 233: :np:nc:sp#230400:
FreeBSD-CVSweb <freebsd-cvsweb@FreeBSD.org>
![[BACK]](/icons/cvsweb/back.gif){kind=icon}
Return to gettytab CVS log ![[TXT]](/icons/cvsweb/text.gif){kind=icon}
![[DIR]](/icons/cvsweb/dir.gif){kind=icon}
Up to [ELWIX - Embedded LightWeight unIX -] / elwix / config / etc / uboot