--- elwix/config/etc/uboot/snmpd.config	2014/01/23 09:24:03	1.1
+++ elwix/config/etc/uboot/snmpd.config	2014/09/15 19:06:48	1.2
@@ -0,0 +1,302 @@
+# $FreeBSD: src/etc/snmpd.config,v 1.14 2012/11/17 01:49:02 svnexp Exp $
+#
+# Example configuration file for bsnmpd(1).
+#
+
+#
+# Set some common variables
+#
+location := "Room 200"
+contact := "sysmeister@elwix.org"
+system := 1	# FreeBSD
+traphost := localhost
+trapport := 162
+
+#
+# Set the SNMP engine ID.
+#
+# The snmpEngineID object required from the SNMPv3 Framework. If not explicitly set via
+# this configuration file, an ID is assigned based on the value of the
+# kern.hostid variable
+# engine := 0x80:0x10:0x08:0x10:0x80:0x25
+# snmpEngineID = $(engine)
+
+# Change this!
+read := "public"
+# Uncomment begemotSnmpdCommunityString.0.2 below that sets the community
+# string to enable write access.
+write := "geheim"
+trap := "mytrap"
+
+#
+# Declarations for SNMP-USER-BASED-SM-MIB authentication and privacy options
+#
+
+NoAuthProtocol		:= 1.3.6.1.6.3.10.1.1.1
+HMACMD5AuthProtocol	:= 1.3.6.1.6.3.10.1.1.2
+HMACSHAAuthProtocol	:= 1.3.6.1.6.3.10.1.1.3
+NoPrivProtocol		:= 1.3.6.1.6.3.10.1.2.1
+DESPrivProtocol		:= 1.3.6.1.6.3.10.1.2.2
+AesCfb128Protocol	:= 1.3.6.1.6.3.10.1.2.4
+
+#
+# Enumerations from SNMP-FRAMEWORK-MIB
+#
+
+# Security models
+securityModelAny	:= 0
+securityModelSNMPv1	:= 1
+securityModelSNMPv2c	:= 2
+securityModelUSM	:= 3
+
+# Message Processing models
+MPmodelSNMPv1		:= 0
+MPmodelSNMPv2c		:= 1
+MPmodelSNMPv3		:= 3
+
+# Security levels
+noAuthNoPriv := 1
+authNoPriv := 2
+authPriv := 3
+
+
+# SNMPv3 USM User definition
+#
+# The localized hex password for a user may be obtained by setting SNMPUSER, SNMPPASSWD,
+# SNMPAUTH and SNMPPRIV environment variables to the desired parameters and invoking
+# 'bsnmpget -v 3 -D -K -o verbose' against the running bsnmpd(1). For other
+# usages refer to the bsnmpget(1) manual page. The following lines define a user "bsnmp"
+# with a private password "bsnmptest", localized for the above engine ID.
+#
+#user1 := "bsnmp"
+#user1passwd := 0x22:0x98:0x1a:0x6e:0x39:0x93:0x16:0x5e:0x6a:0x21:0x1b:0xd8:0xa9:0x81:0x31:0x05:0x16:0x33:0x38:0x60
+
+#
+# Configuration
+#
+%snmpd
+begemotSnmpdDebugDumpPdus	= 2
+begemotSnmpdDebugSyslogPri	= 7
+
+#
+# Set the read and write communities.
+#
+# The default value of the community strings is NULL (note, that this is
+# different from the empty string). This disables both read and write access.
+# To enable read access only the read community string must be set. Setting
+# the write community string enables both read and write access with that
+# string.
+#
+# Be sure to understand the security implications of SNMPv2 - the community
+# strings are readable on the wire!
+#
+begemotSnmpdCommunityString.0.1	= $(read)
+# begemotSnmpdCommunityString.0.2	= $(write)
+begemotSnmpdCommunityDisable	= 1
+
+# open standard SNMP ports
+begemotSnmpdPortStatus.0.0.0.0.161 = 1
+
+# open a unix domain socket
+begemotSnmpdLocalPortStatus."/var/run/snmpd.sock" = 1
+begemotSnmpdLocalPortType."/var/run/snmpd.sock" = 4
+
+# send traps to the traphost
+begemotTrapSinkStatus.[$(traphost)].$(trapport) = 4
+begemotTrapSinkVersion.[$(traphost)].$(trapport) = 2
+begemotTrapSinkComm.[$(traphost)].$(trapport) = $(trap)
+
+sysContact	= $(contact)
+sysLocation	= $(location)
+sysObjectId 	= 1.3.6.1.4.1.12325.1.1.2.1.$(system)
+
+snmpEnableAuthenTraps = 2
+
+#
+# SNMPv3 User-based security module - must be loaded for SNMPv3 USM
+#
+#begemotSnmpdModulePath."usm"	= "/usr/lib/snmp_usm.so"
+
+#
+# SNMPv3 USM User definition.
+#
+
+#%usm
+
+#
+# The following block creates a user with name "bsnmp" and sets privacy
+# and encryption options to SHA256 message digests and AES encryption
+# for this user.
+# 
+# usmUserStatus.$(engine).$(user1) = 5
+# usmUserAuthProtocol.$(engine).$(user1) = $(HMACSHAAuthProtocol)
+# usmUserAuthKeyChange.$(engine).$(user1) = $(user1passwd)
+# usmUserPrivProtocol.$(engine).$(user1) = $(AesCfb128Protocol)
+# usmUserPrivKeyChange.$(engine).$(user1) = $(user1passwd)
+# usmUserStatus.$(engine).$(user1) = 1
+#
+
+#
+# The following block creates a user with name "public" with no authentication
+# or encryption options.
+#
+# usmUserStatus.$(engine).$(read) = 5
+# usmUserAuthProtocol.$(engine).$(read) = $(NoAuthProtocol)
+# usmUserPrivProtocol.$(engine).$(read) = $(NoPrivProtocol)
+# usmUserStatus.$(engine).$(read) = 1
+#
+
+#
+# SNMPv3 View-based Access Control module
+#
+#begemotSnmpdModulePath."vacm"	= "/usr/lib/snmp_vacm.so"
+
+#
+# Definition of view-based access control entries.
+#
+#%vacm
+
+# Definition of a SNMPv1 group
+# vacmSecurityToGroupStatus.$(securityModelSNMPv1).$(read) = 4
+# vacmGroupName.$(securityModelSNMPv1).$(read) = $(read)
+
+# Definition of SNMPv2 group
+# vacmSecurityToGroupStatus.$(securityModelSNMPv2c).$(write) = 4
+# vacmGroupName.$(securityModelSNMPv2c).$(write) = $(write)
+
+# Definition of SNMPv3 group with users "bsnmp" and "public"
+# vacmSecurityToGroupStatus.$(securityModelUSM).$(user1) = 4
+# vacmGroupName.$(securityModelUSM).$(user1) = $(write)
+# vacmSecurityToGroupStatus.$(securityModelUSM).$(read) = 4
+# vacmGroupName.$(securityModelUSM).$(read) = $(write)
+
+# 
+# The OID of the .iso.org.dod.internet subtree
+#
+# internetoid := 1.3.6.1
+# internetoidlen := 4
+
+#
+# Definitions of two views
+#
+# vacmViewTreeFamilyStatus."internet".$(internetoidlen).$(internetoid) = 4
+# vacmViewTreeFamilyStatus."restricted".$(internetoidlen).$(internetoid) = 4
+
+#
+# Access control
+#
+
+#
+# Read-only access for SNMPv1 users
+#
+# vacmAccessStatus.$(read)."".$(securityModelSNMPv1).$(noAuthNoPriv) = 4
+# vacmAccessReadViewName.$(read)."".$(securityModelSNMPv1).$(noAuthNoPriv) = "internet"
+
+#
+# Read-write access for SNMPv2 users 
+#
+# vacmAccessStatus.$(write)."".$(securityModelSNMPv2c).$(noAuthNoPriv) = 4
+# vacmAccessReadViewName.$(write)."".$(securityModelSNMPv2c).$(noAuthNoPriv) = "internet"
+# vacmAccessWriteViewName.$(write)."".$(securityModelSNMPv2c).$(noAuthNoPriv) = "internet"
+
+#
+# Read-write-notify access for SNMPv3 USM users with noAuthNoPriv
+#
+# vacmAccessStatus.$(write)."".3.$(noAuthNoPriv) = 4
+# vacmAccessReadViewName.$(write)."".$(securityModelUSM).$(noAuthNoPriv) = "internet"
+# vacmAccessWriteViewName.$(write)."".$(securityModelUSM).$(noAuthNoPriv) = "internet"
+# vacmAccessNotifyViewName.$(write)."".$(securityModelUSM).$(noAuthNoPriv) = "internet"
+
+#
+#Read-write-notify access to restricted for SNMPv3 USM users with authPriv
+#
+# vacmAccessStatus.$(write)."".3.$(authPriv) = 4
+# vacmAccessReadViewName.$(write)."".3.$(authPriv) = "restricted"
+# vacmAccessWriteViewName.$(write)."".3.$(authPriv) = "restricted"
+# vacmAccessNotifyViewName.$(write)."".3.$(authPriv) = "restricted"
+
+#
+# SNMPv3 Notification Targets
+#
+# begemotSnmpdModulePath."target"	= "/usr/lib/snmp_target.so"
+
+#%target
+# Send notifications to target tag "test"
+# tag		:= "test"
+# snmpNotifyRowStatus.$(tag) = 4
+# snmpNotifyTag.$(tag) = $(tag)
+
+# tagremote		:= "testremote"
+# snmpNotifyRowStatus.$(tagremote) = 4
+# snmpNotifyTag.$(tagremote) = $(tagremote)
+
+#
+# Specify the target parameters for the notifications - send with the credentials
+# of user "bsnmp"
+#
+# snmpTargetParamsRowStatus.$(tag) = 5
+# snmpTargetParamsMPModel.$(tag) = $(MPmodelSNMPv3)
+# snmpTargetParamsSecurityModel.$(tag) = $(securityModelUSM)
+# snmpTargetParamsSecurityName.$(tag) = $(user1)
+# snmpTargetParamsSecurityLevel.$(tag) = $(authPriv)
+# snmpTargetParamsRowStatus.$(tag) = 1
+
+#
+# Define the notifications' target address - port 162 on localhost
+#
+# snmpTargetAddrRowStatus.$(tag) = 5
+# snmpTargetAddrTAddress.$(tag) = 0x7f:0x0:0x0:0x1:0x0:0xa2
+# snmpTargetAddrTagList.$(tag) = "test notification"
+# snmpTargetAddrParams.$(tag) = $(tag)
+# snmpTargetAddrRowStatus.$(tag) = 1
+
+#
+# Define the notifications' target address - port 162 on 10.0.0.1
+#
+# snmpTargetAddrRowStatus.$(tagremote) = 5
+# snmpTargetAddrTAddress.$(tagremote) = 0x0a:0x00:0x00:0x1:0x0:0xa2
+# snmpTargetAddrTagList.$(tagremote) = $(tagremote)
+# snmpTargetAddrParams.$(tagremote) = $(tag)
+# snmpTargetAddrRowStatus.$(tagremote) = 1
+
+#
+# Load MIB-2 module
+#
+begemotSnmpdModulePath."mibII"	= "/usr/lib/snmp_mibII.so"
+
+# Force a polling rate for the 64-bit interface counters in case
+# the automatic computation is wrong (which may be the case if an interface
+# announces the wrong bit rate via its MIB).
+#%mibII
+#begemotIfForcePoll = 2000
+
+
+# Netgraph module
+#
+#begemotSnmpdModulePath."netgraph" = "/usr/lib/snmp_netgraph.so"
+#
+#%netgraph
+#begemotNgControlNodeName = "snmpd"
+
+#
+# pf(4) module
+#
+#begemotSnmpdModulePath."pf"	= "/usr/lib/snmp_pf.so"
+
+#
+# Host resources module
+#  This requires the mibII module.
+#
+#begemotSnmpdModulePath."hostres" = "/usr/lib/snmp_hostres.so"
+
+#
+# Bridge module
+#  This requires the mibII module.
+#
+#begemotSnmpdModulePath."bridge" = "/usr/lib/snmp_bridge.so"
+
+#
+# Wireless module
+#  This requires the mibII module.
+#
+#begemotSnmpdModulePath."wlan" = "/usr/lib/snmp_wlan.so"