Return to snmpd.config CVS log | Up to [ELWIX - Embedded LightWeight unIX -] / elwix / config / etc / uboot |
1.2 misho 1: # $FreeBSD: src/etc/snmpd.config,v 1.14 2012/11/17 01:49:02 svnexp Exp $ 2: # 3: # Example configuration file for bsnmpd(1). 4: # 5: 6: # 7: # Set some common variables 8: # 1.3 ! misho 9: location := "ELWIX" 1.2 misho 10: contact := "sysmeister@elwix.org" 11: system := 1 # FreeBSD 12: traphost := localhost 13: trapport := 162 14: 15: # 16: # Set the SNMP engine ID. 17: # 18: # The snmpEngineID object required from the SNMPv3 Framework. If not explicitly set via 19: # this configuration file, an ID is assigned based on the value of the 20: # kern.hostid variable 21: # engine := 0x80:0x10:0x08:0x10:0x80:0x25 22: # snmpEngineID = $(engine) 23: 24: # Change this! 1.3 ! misho 25: read := "elwix" 1.2 misho 26: # Uncomment begemotSnmpdCommunityString.0.2 below that sets the community 27: # string to enable write access. 1.3 ! misho 28: write := "31w1x" ! 29: trap := "ELWIX" 1.2 misho 30: 31: # 32: # Declarations for SNMP-USER-BASED-SM-MIB authentication and privacy options 33: # 34: 35: NoAuthProtocol := 1.3.6.1.6.3.10.1.1.1 36: HMACMD5AuthProtocol := 1.3.6.1.6.3.10.1.1.2 37: HMACSHAAuthProtocol := 1.3.6.1.6.3.10.1.1.3 38: NoPrivProtocol := 1.3.6.1.6.3.10.1.2.1 39: DESPrivProtocol := 1.3.6.1.6.3.10.1.2.2 40: AesCfb128Protocol := 1.3.6.1.6.3.10.1.2.4 41: 42: # 43: # Enumerations from SNMP-FRAMEWORK-MIB 44: # 45: 46: # Security models 47: securityModelAny := 0 48: securityModelSNMPv1 := 1 49: securityModelSNMPv2c := 2 50: securityModelUSM := 3 51: 52: # Message Processing models 53: MPmodelSNMPv1 := 0 54: MPmodelSNMPv2c := 1 55: MPmodelSNMPv3 := 3 56: 57: # Security levels 58: noAuthNoPriv := 1 59: authNoPriv := 2 60: authPriv := 3 61: 62: 63: # SNMPv3 USM User definition 64: # 65: # The localized hex password for a user may be obtained by setting SNMPUSER, SNMPPASSWD, 66: # SNMPAUTH and SNMPPRIV environment variables to the desired parameters and invoking 67: # 'bsnmpget -v 3 -D -K -o verbose' against the running bsnmpd(1). For other 68: # usages refer to the bsnmpget(1) manual page. The following lines define a user "bsnmp" 69: # with a private password "bsnmptest", localized for the above engine ID. 70: # 71: #user1 := "bsnmp" 72: #user1passwd := 0x22:0x98:0x1a:0x6e:0x39:0x93:0x16:0x5e:0x6a:0x21:0x1b:0xd8:0xa9:0x81:0x31:0x05:0x16:0x33:0x38:0x60 73: 74: # 75: # Configuration 76: # 77: %snmpd 78: begemotSnmpdDebugDumpPdus = 2 79: begemotSnmpdDebugSyslogPri = 7 80: 81: # 82: # Set the read and write communities. 83: # 84: # The default value of the community strings is NULL (note, that this is 85: # different from the empty string). This disables both read and write access. 86: # To enable read access only the read community string must be set. Setting 87: # the write community string enables both read and write access with that 88: # string. 89: # 90: # Be sure to understand the security implications of SNMPv2 - the community 91: # strings are readable on the wire! 92: # 93: begemotSnmpdCommunityString.0.1 = $(read) 94: # begemotSnmpdCommunityString.0.2 = $(write) 95: begemotSnmpdCommunityDisable = 1 96: 97: # open standard SNMP ports 98: begemotSnmpdPortStatus.0.0.0.0.161 = 1 99: 100: # open a unix domain socket 101: begemotSnmpdLocalPortStatus."/var/run/snmpd.sock" = 1 102: begemotSnmpdLocalPortType."/var/run/snmpd.sock" = 4 103: 104: # send traps to the traphost 105: begemotTrapSinkStatus.[$(traphost)].$(trapport) = 4 106: begemotTrapSinkVersion.[$(traphost)].$(trapport) = 2 107: begemotTrapSinkComm.[$(traphost)].$(trapport) = $(trap) 108: 109: sysContact = $(contact) 110: sysLocation = $(location) 111: sysObjectId = 1.3.6.1.4.1.12325.1.1.2.1.$(system) 112: 113: snmpEnableAuthenTraps = 2 114: 115: # 116: # SNMPv3 User-based security module - must be loaded for SNMPv3 USM 117: # 118: #begemotSnmpdModulePath."usm" = "/usr/lib/snmp_usm.so" 119: 120: # 121: # SNMPv3 USM User definition. 122: # 123: 124: #%usm 125: 126: # 127: # The following block creates a user with name "bsnmp" and sets privacy 128: # and encryption options to SHA256 message digests and AES encryption 129: # for this user. 130: # 131: # usmUserStatus.$(engine).$(user1) = 5 132: # usmUserAuthProtocol.$(engine).$(user1) = $(HMACSHAAuthProtocol) 133: # usmUserAuthKeyChange.$(engine).$(user1) = $(user1passwd) 134: # usmUserPrivProtocol.$(engine).$(user1) = $(AesCfb128Protocol) 135: # usmUserPrivKeyChange.$(engine).$(user1) = $(user1passwd) 136: # usmUserStatus.$(engine).$(user1) = 1 137: # 138: 139: # 140: # The following block creates a user with name "public" with no authentication 141: # or encryption options. 142: # 143: # usmUserStatus.$(engine).$(read) = 5 144: # usmUserAuthProtocol.$(engine).$(read) = $(NoAuthProtocol) 145: # usmUserPrivProtocol.$(engine).$(read) = $(NoPrivProtocol) 146: # usmUserStatus.$(engine).$(read) = 1 147: # 148: 149: # 150: # SNMPv3 View-based Access Control module 151: # 152: #begemotSnmpdModulePath."vacm" = "/usr/lib/snmp_vacm.so" 153: 154: # 155: # Definition of view-based access control entries. 156: # 157: #%vacm 158: 159: # Definition of a SNMPv1 group 160: # vacmSecurityToGroupStatus.$(securityModelSNMPv1).$(read) = 4 161: # vacmGroupName.$(securityModelSNMPv1).$(read) = $(read) 162: 163: # Definition of SNMPv2 group 164: # vacmSecurityToGroupStatus.$(securityModelSNMPv2c).$(write) = 4 165: # vacmGroupName.$(securityModelSNMPv2c).$(write) = $(write) 166: 167: # Definition of SNMPv3 group with users "bsnmp" and "public" 168: # vacmSecurityToGroupStatus.$(securityModelUSM).$(user1) = 4 169: # vacmGroupName.$(securityModelUSM).$(user1) = $(write) 170: # vacmSecurityToGroupStatus.$(securityModelUSM).$(read) = 4 171: # vacmGroupName.$(securityModelUSM).$(read) = $(write) 172: 173: # 174: # The OID of the .iso.org.dod.internet subtree 175: # 176: # internetoid := 1.3.6.1 177: # internetoidlen := 4 178: 179: # 180: # Definitions of two views 181: # 182: # vacmViewTreeFamilyStatus."internet".$(internetoidlen).$(internetoid) = 4 183: # vacmViewTreeFamilyStatus."restricted".$(internetoidlen).$(internetoid) = 4 184: 185: # 186: # Access control 187: # 188: 189: # 190: # Read-only access for SNMPv1 users 191: # 192: # vacmAccessStatus.$(read)."".$(securityModelSNMPv1).$(noAuthNoPriv) = 4 193: # vacmAccessReadViewName.$(read)."".$(securityModelSNMPv1).$(noAuthNoPriv) = "internet" 194: 195: # 196: # Read-write access for SNMPv2 users 197: # 198: # vacmAccessStatus.$(write)."".$(securityModelSNMPv2c).$(noAuthNoPriv) = 4 199: # vacmAccessReadViewName.$(write)."".$(securityModelSNMPv2c).$(noAuthNoPriv) = "internet" 200: # vacmAccessWriteViewName.$(write)."".$(securityModelSNMPv2c).$(noAuthNoPriv) = "internet" 201: 202: # 203: # Read-write-notify access for SNMPv3 USM users with noAuthNoPriv 204: # 205: # vacmAccessStatus.$(write)."".3.$(noAuthNoPriv) = 4 206: # vacmAccessReadViewName.$(write)."".$(securityModelUSM).$(noAuthNoPriv) = "internet" 207: # vacmAccessWriteViewName.$(write)."".$(securityModelUSM).$(noAuthNoPriv) = "internet" 208: # vacmAccessNotifyViewName.$(write)."".$(securityModelUSM).$(noAuthNoPriv) = "internet" 209: 210: # 211: #Read-write-notify access to restricted for SNMPv3 USM users with authPriv 212: # 213: # vacmAccessStatus.$(write)."".3.$(authPriv) = 4 214: # vacmAccessReadViewName.$(write)."".3.$(authPriv) = "restricted" 215: # vacmAccessWriteViewName.$(write)."".3.$(authPriv) = "restricted" 216: # vacmAccessNotifyViewName.$(write)."".3.$(authPriv) = "restricted" 217: 218: # 219: # SNMPv3 Notification Targets 220: # 221: # begemotSnmpdModulePath."target" = "/usr/lib/snmp_target.so" 222: 223: #%target 224: # Send notifications to target tag "test" 225: # tag := "test" 226: # snmpNotifyRowStatus.$(tag) = 4 227: # snmpNotifyTag.$(tag) = $(tag) 228: 229: # tagremote := "testremote" 230: # snmpNotifyRowStatus.$(tagremote) = 4 231: # snmpNotifyTag.$(tagremote) = $(tagremote) 232: 233: # 234: # Specify the target parameters for the notifications - send with the credentials 235: # of user "bsnmp" 236: # 237: # snmpTargetParamsRowStatus.$(tag) = 5 238: # snmpTargetParamsMPModel.$(tag) = $(MPmodelSNMPv3) 239: # snmpTargetParamsSecurityModel.$(tag) = $(securityModelUSM) 240: # snmpTargetParamsSecurityName.$(tag) = $(user1) 241: # snmpTargetParamsSecurityLevel.$(tag) = $(authPriv) 242: # snmpTargetParamsRowStatus.$(tag) = 1 243: 244: # 245: # Define the notifications' target address - port 162 on localhost 246: # 247: # snmpTargetAddrRowStatus.$(tag) = 5 248: # snmpTargetAddrTAddress.$(tag) = 0x7f:0x0:0x0:0x1:0x0:0xa2 249: # snmpTargetAddrTagList.$(tag) = "test notification" 250: # snmpTargetAddrParams.$(tag) = $(tag) 251: # snmpTargetAddrRowStatus.$(tag) = 1 252: 253: # 254: # Define the notifications' target address - port 162 on 10.0.0.1 255: # 256: # snmpTargetAddrRowStatus.$(tagremote) = 5 257: # snmpTargetAddrTAddress.$(tagremote) = 0x0a:0x00:0x00:0x1:0x0:0xa2 258: # snmpTargetAddrTagList.$(tagremote) = $(tagremote) 259: # snmpTargetAddrParams.$(tagremote) = $(tag) 260: # snmpTargetAddrRowStatus.$(tagremote) = 1 261: 262: # 263: # Load MIB-2 module 264: # 265: begemotSnmpdModulePath."mibII" = "/usr/lib/snmp_mibII.so" 266: 267: # Force a polling rate for the 64-bit interface counters in case 268: # the automatic computation is wrong (which may be the case if an interface 269: # announces the wrong bit rate via its MIB). 270: #%mibII 271: #begemotIfForcePoll = 2000 272: 273: 274: # Netgraph module 275: # 276: #begemotSnmpdModulePath."netgraph" = "/usr/lib/snmp_netgraph.so" 277: # 278: #%netgraph 279: #begemotNgControlNodeName = "snmpd" 280: 281: # 282: # pf(4) module 283: # 284: #begemotSnmpdModulePath."pf" = "/usr/lib/snmp_pf.so" 285: 286: # 287: # Host resources module 288: # This requires the mibII module. 289: # 290: #begemotSnmpdModulePath."hostres" = "/usr/lib/snmp_hostres.so" 291: 292: # 293: # Bridge module 294: # This requires the mibII module. 295: # 296: #begemotSnmpdModulePath."bridge" = "/usr/lib/snmp_bridge.so" 297: 298: # 299: # Wireless module 300: # This requires the mibII module. 301: # 302: #begemotSnmpdModulePath."wlan" = "/usr/lib/snmp_wlan.so"