Next Previous Contents

4. Remote control

You can use the command-line client birdc to talk with a running BIRD. Communication is done using a bird.ctl UNIX domain socket (unless changed with the -s option given to both the server and the client). The commands can perform simple actions such as enabling/disabling of protocols, telling BIRD to show various information, telling it to show routing table filtered by filter, or asking BIRD to reconfigure. Press ? at any time to get online help. Option -r can be used to enable a restricted mode of BIRD client, which allows just read-only commands (show ...). Option -v can be passed to the client, to make it dump numeric return codes along with the messages. You do not necessarily need to use birdc to talk to BIRD, your own applications could do that, too -- the format of communication between BIRD and birdc is stable (see the programmer's documentation).

There is also lightweight variant of BIRD client called birdcl, which does not support command line editing and history and has minimal dependencies. This is useful for running BIRD in resource constrained environments, where Readline library (required for regular BIRD client) is not available.

Many commands have the name of the protocol instance as an argument. This argument can be omitted if there exists only a single instance.

Here is a brief list of supported functions:

show status

Show router status, that is BIRD version, uptime and time from last reconfiguration.

show interfaces [summary]

Show the list of interfaces. For each interface, print its type, state, MTU and addresses assigned.

show protocols [all]

Show list of protocol instances along with tables they are connected to and protocol status, possibly giving verbose information, if all is specified.

show ospf interface [name] ["interface"]

Show detailed information about OSPF interfaces.

show ospf neighbors [name] ["interface"]

Show a list of OSPF neighbors and a state of adjacency to them.

show ospf state [all] [name]

Show detailed information about OSPF areas based on a content of the link-state database. It shows network topology, stub networks, aggregated networks and routers from other areas and external routes. The command shows information about reachable network nodes, use option all to show information about all network nodes in the link-state database.

show ospf topology [all] [name]

Show a topology of OSPF areas based on a content of the link-state database. It is just a stripped-down version of 'show ospf state'.

show ospf lsadb [global | area id | link] [type num] [lsid id] [self | router id] [name]

Show contents of an OSPF LSA database. Options could be used to filter entries.

show rip interfaces [name] ["interface"]

Show detailed information about RIP interfaces.

show rip neighbors [name] ["interface"]

Show a list of RIP neighbors and associated state.

show static [name]

Show detailed information about static routes.

show bfd sessions [name]

Show information about BFD sessions.

show symbols [table|filter|function|protocol|template|roa|symbol]

Show the list of symbols defined in the configuration (names of protocols, routing tables etc.).

show route [[for] prefix|IP] [table t] [filter f|where c] [(export|preexport|noexport) p] [protocol p] [options]

Show contents of a routing table (by default of the main one or the table attached to a respective protocol), that is routes, their metrics and (in case the all switch is given) all their attributes.

You can specify a prefix if you want to print routes for a specific network. If you use for prefix or IP, you'll get the entry which will be used for forwarding of packets to the given destination. By default, all routes for each network are printed with the selected one at the top, unless primary is given in which case only the selected route is shown.

You can also ask for printing only routes processed and accepted by a given filter (filter name or filter { filter } or matching a given condition (where condition).

The export, preexport and noexport switches ask for printing of routes that are exported to the specified protocol. With preexport, the export filter of the protocol is skipped. With noexport, routes rejected by the export filter are printed instead. Note that routes not exported to the protocol for other reasons (e.g. secondary routes or routes imported from that protocol) are not printed even with noexport.

You can also select just routes added by a specific protocol. protocol p.

If BIRD is configured to keep filtered routes (see import keep filtered option), you can show them instead of routes by using filtered switch.

The stats switch requests showing of route statistics (the number of networks, number of routes before and after filtering). If you use count instead, only the statistics will be printed.

show roa [prefix | in prefix | for prefix] [as num] [table t]

Show contents of a ROA table (by default of the first one). You can specify a prefix to print ROA entries for a specific network. If you use for prefix, you'll get all entries relevant for route validation of the network prefix; i.e., ROA entries whose prefixes cover the network prefix. Or you can use in prefix to get ROA entries covered by the network prefix. You could also use as option to show just entries for given AS.

add roa prefix max num as num [table t]

Add a new ROA entry to a ROA table. Such entry is called dynamic compared to static entries specified in the config file. These dynamic entries survive reconfiguration.

delete roa prefix max num as num [table t]

Delete the specified ROA entry from a ROA table. Only dynamic ROA entries (i.e., the ones added by add roa command) can be deleted.

flush roa [table t]

Remove all dynamic ROA entries from a ROA table.

configure [soft] ["config file"] [timeout [num]]

Reload configuration from a given file. BIRD will smoothly switch itself to the new configuration, protocols are reconfigured if possible, restarted otherwise. Changes in filters usually lead to restart of affected protocols.

If soft option is used, changes in filters does not cause BIRD to restart affected protocols, therefore already accepted routes (according to old filters) would be still propagated, but new routes would be processed according to the new filters.

If timeout option is used, config timer is activated. The new configuration could be either confirmed using configure confirm command, or it will be reverted to the old one when the config timer expires. This is useful for cases when reconfiguration breaks current routing and a router becomes inaccessible for an administrator. The config timeout expiration is equivalent to configure undo command. The timeout duration could be specified, default is 300 s.

configure confirm

Deactivate the config undo timer and therefore confirm the current configuration.

configure undo

Undo the last configuration change and smoothly switch back to the previous (stored) configuration. If the last configuration change was soft, the undo change is also soft. There is only one level of undo, but in some specific cases when several reconfiguration requests are given immediately in a row and the intermediate ones are skipped then the undo also skips them back.

configure check ["config file"]

Read and parse given config file, but do not use it. useful for checking syntactic and some semantic validity of an config file.

enable|disable|restart name|"pattern"|all

Enable, disable or restart a given protocol instance, instances matching the pattern or all instances.

reload [in|out] name|"pattern"|all

Reload a given protocol instance, that means re-import routes from the protocol instance and re-export preferred routes to the instance. If in or out options are used, the command is restricted to one direction (re-import or re-export).

This command is useful if appropriate filters have changed but the protocol instance was not restarted (or reloaded), therefore it still propagates the old set of routes. For example when configure soft command was used to change filters.

Re-export always succeeds, but re-import is protocol-dependent and might fail (for example, if BGP neighbor does not support route-refresh extension). In that case, re-export is also skipped. Note that for the pipe protocol, both directions are always reloaded together (in or out options are ignored in that case).

down

Shut BIRD down.

debug protocol|pattern|all all|off|{ states|routes|filters|events|packets [, ...] }

Control protocol debugging.

dump resources|sockets|interfaces|neighbors|attributes|routes|protocols

Dump contents of internal data structures to the debugging output.

echo all|off|{ list of log classes } [ buffer-size ]

Control echoing of log messages to the command-line output. See log option for a list of log classes.

eval expr

Evaluate given expression.


Next Previous Contents