Annotation of embedaddon/freevrrpd/freevrrpd.conf.sample, revision 1.1.1.1
1.1 misho 1: # This is a simple configuration file for freevrrpd
2: # Please read the documentation before modifying these parameters
3: # I recommend to not set addr to the unique and real ip of your server because
4: # if freevrrpd will shutdown, your server will don't have any IP address.
5: # a good utilization is to set a real IP address not managed by freevrrpd and
6: # then choosing an alias for the virtual IP address managed by freevrrpd
7: #
8: # Each VRID Section must begin with [VRID] keyword
9:
10: [VRID]
11: # serverid is needed to specify the number of the VRID, here VRID = 1
12: serverid = 1
13:
14: # you must set interface with a real interface name of your system
15: # this interface is used for sending VRRP announces
16: interface = rl0
17:
18: # this option specify a timeout for an interface like bge/em go down and up
19: # when an ethernet (lladdr) adress is setted on it. em/bge take about 2/3
20: # secondes before becoming up and running after transiting MASTER/BACKUP states
21: # the default is 10 seconds and must work with all NICs without problems
22: carriertimeout = 10
23:
24: # this option must be set for switches that have spanning tree activated
25: # because there is a time between the port activation and the first VLANs
26: # packets received. A value of 40 seconds will be good.
27: # by default, spanningtreelatency is disabled (=0)
28: spanningtreelatency = 0
29:
30: # priority = 255 is a MASTER of the VRID
31: # priority < 255 is a BACKUP with a priority 0 to 254
32: # 254 is a higher BACKUP priority
33: priority = 255
34:
35: # addr option is need to specify ip address(es) associated with the VRID
36: # you can specify multiple addresses separated by ','
37: # netmask is specified with CIDR notation so number after '/' represent the
38: # number of bits set to 1 for the netmask.
39: # eg: /24 is 11111111 11111111 11111111 00000000 = 255.255.255.0
40: # you can specify another (pseudo-)device for setting this(ese) adress(es)
41: addr = 10.0.0.1/32, vlan100:192.168.1.1/30, vlan101:192.168.10.1/30
42:
43: # Monitored circuits (test of carrier, interface and duplex) can be enabled
44: # or disabled. it's enabled by default but you may want to deactivate it for
45: # old NIC drivers that d'ont support mii bus
46: monitoredcircuits = yes
47:
48: # Specify the number of concurrent checks on a NIC by monitored circuits
49: # before considering to reset the error counter on this NIC. The default value
50: # is 3600 concurrent checks (about 1 hour)
51: # if 0 is specified, nberrors wil be never resetted
52: MCClearErrorsCount = 3600
53:
54: # now, you can specify a script name to execute when this host became master
55: # of this VRID
56: masterscript = /usr/local/bin/master_script.sh
57:
58: # and you can specify a script name to execute when this host became backup
59: # too
60: backupscript = /usr/local/bin/backup_script.sh
61:
62: # if physical interface attached to VRID 1 fail you can specify one or more
63: # VRIDs that must go to backup state in the same time. (monitored circuits)
64: # in this example if rl0 is faulty, xl0 and bge0 go to backup state mode
65: # This is extremly useful to avoir blackhole with Firewalls with two interfaces
66: vridsdep = 2, 3
67:
68: # if you want to authenticate your VRRP packets you can set a password
69: # associated with this VRID. this is not required but is you don't set a
70: # password, everybody in your LAN can generate VRRP packets without
71: # authentification. If you set this, you must set it to BACKUP VRID too, if you
72: # don't, all BACKUP VRRP packets will be rejected.
73: password = vrid1
74:
75: # if you want to authenticate your VRRP packets by AH encryption you must set
76: # this option to yes and specify a presharedkey parameter or useIKE=yes if you
77: # want an external key negociation like IKE (racoon)
78: #AHencryption = no
79:
80: # if you want to use an external key exchanger IKE, let freevrrpd know it with
81: # useIKE = yes
82: #useIKE = no
83:
84: # if you have set AHencryption = yes and useIKE = no you must specify a pre
85: # shared key known by VRRP servers that is on the same VRID, you can specify
86: # the key with this option
87: #presharedkey = blahblah
88:
89: [VRID]
90: # specify a second VRID number 2
91: serverid = 2
92: interface = xl0
93: # priority = 100 so it's a backup
94: priority = 100
95: addr = 192.168.1.2/32
96: password = vrid2
97: [VRID]
98: serverid = 3
99: interface = bge0
100: priority = 255
101: addr = 192.168.2.2/32
102: password = vrid3
FreeBSD-CVSweb <freebsd-cvsweb@FreeBSD.org>