Return to ripngd.texi CVS log

Up to [ELWIX - Embedded LightWeight unIX -] / embedaddon / quagga / doc

Annotation of embedaddon/quagga/doc/ripngd.texi, revision 1.1

1.1     ! misho       1: @c -*-texinfo-*-
        !             2: @c This is part of the Quagga Manual.
        !             3: @c @value{COPYRIGHT_STR}
        !             4: @c See file quagga.texi for copying conditions.
        !             5: @node RIPng
        !             6: @chapter RIPng
        !             7: 
        !             8: @command{ripngd} supports the RIPng protocol as described in RFC2080.  It's an
        !             9: IPv6 reincarnation of the RIP protocol.
        !            10: 
        !            11: @menu
        !            12: * Invoking ripngd::             
        !            13: * ripngd Configuration::        
        !            14: * ripngd Terminal Mode Commands::  
        !            15: * ripngd Filtering Commands::   
        !            16: @end menu
        !            17: 
        !            18: @node Invoking ripngd
        !            19: @section Invoking ripngd
        !            20: 
        !            21: There are no @code{ripngd} specific invocation options.  Common options
        !            22: can be specified (@pxref{Common Invocation Options}).
        !            23: 
        !            24: @node ripngd Configuration
        !            25: @section ripngd Configuration
        !            26: 
        !            27: Currently ripngd supports the following commands:
        !            28: 
        !            29: @deffn Command {router ripng} {}
        !            30: Enable RIPng.
        !            31: @end deffn
        !            32: 
        !            33: @deffn {RIPng Command} {flush_timer @var{time}} {}
        !            34: Set flush timer.
        !            35: @end deffn
        !            36: 
        !            37: @deffn {RIPng Command} {network @var{network}} {}
        !            38: Set RIPng enabled interface by @var{network}
        !            39: @end deffn
        !            40: 
        !            41: @deffn {RIPng Command} {network @var{ifname}} {}
        !            42: Set RIPng enabled interface by @var{ifname}
        !            43: @end deffn
        !            44: 
        !            45: @deffn {RIPng Command} {route @var{network}} {}
        !            46: Set RIPng static routing announcement of @var{network}.
        !            47: @end deffn
        !            48: 
        !            49: @deffn Command {router zebra} {}
        !            50: This command is the default and does not appear in the configuration.
        !            51: With this statement, RIPng routes go to the @command{zebra} daemon.
        !            52: @end deffn
        !            53: 
        !            54: @node ripngd Terminal Mode Commands
        !            55: @section ripngd Terminal Mode Commands
        !            56: 
        !            57: @deffn Command {show ip ripng} {}
        !            58: @end deffn
        !            59: 
        !            60: @deffn Command {show debugging ripng} {}
        !            61: @end deffn
        !            62: 
        !            63: @deffn Command {debug ripng events} {}
        !            64: @end deffn
        !            65: 
        !            66: @deffn Command {debug ripng packet} {}
        !            67: @end deffn
        !            68: 
        !            69: @deffn Command {debug ripng zebra} {}
        !            70: @end deffn
        !            71: 
        !            72: @node ripngd Filtering Commands
        !            73: @section ripngd Filtering Commands
        !            74: 
        !            75: @deffn Command {distribute-list @var{access_list} (in|out) @var{ifname}} {}
        !            76: You can apply an access-list to the interface using the
        !            77: @code{distribute-list} command.  @var{access_list} is an access-list
        !            78: name.  @var{direct} is @samp{in} or @samp{out}.  If @var{direct} is
        !            79: @samp{in}, the access-list is applied only to incoming packets.
        !            80: 
        !            81: @example
        !            82: distribute-list local-only out sit1
        !            83: @end example
        !            84: @end deffn