Return to README CVS log

Up to [ELWIX - Embedded LightWeight unIX -] / embedaddon / quagga / ospf6d

Annotation of embedaddon/quagga/ospf6d/README, revision 1.1

1.1     ! misho       1: 
        !             2:                  Zebra OSPF daemon for IPv6 network
        !             3: 
        !             4:                             2003/08/18
        !             5: 
        !             6: README for newer code is not yet. General usage should remain
        !             7: the same. For further usage, see command helps by typing '?'
        !             8: in vty, and then imagin ! ;p) Previous README contents follows.
        !             9: 
        !            10:                  Zebra OSPF daemon for IPv6 network
        !            11: 
        !            12:                             2001/12/20
        !            13: 
        !            14: Zebra OSPF6d is OSPF version 3 daemon which is specified by
        !            15: "OSPF for IPv6" (RFC 2740).
        !            16: 
        !            17: *** NOTE ***
        !            18:   Zebra ospf6d is in development yet. It may lack some functionalities,
        !            19:   and may have some bugs. Use the latest version from the anoncvs
        !            20:   repository (http://www.zebra.org/cvs.html) !
        !            21: 
        !            22: This file README is like memo yet, so please feel free to ask
        !            23: <yasu@sfc.wide.ad.jp> by E-mail. Patches will be appriciated.
        !            24: 
        !            25: ospf6d's vty port was default to 2606/tcp.
        !            26: Use commands below.
        !            27: 
        !            28: VIEW NODE:
        !            29:   show ipv6 ospf6
        !            30:     To see Router-ID, uptime of ospf6d, some statistics.
        !            31: 
        !            32:   show ipv6 ospf6 database ...
        !            33:     This command shows LSA database. You can specify
        !            34:     LS-type/LS-ID/Advertising-Router of LSAs. '*' is recognized.
        !            35: 
        !            36:   show ipv6 ospf6 interface ...
        !            37:     To see the status of the OSPF interface, and the configuration
        !            38:     like interface costs.
        !            39: 
        !            40:   show ipv6 ospf6 neighbor ...
        !            41:     Shows state of neighbors and choosed (Backup) DR on the I/F.
        !            42: 
        !            43:   show ipv6 ospf6 route (X::X)
        !            44:     This command shows internal routing table of the ospf6d.
        !            45:     Routes not calculated by OSPFv3 (like connected routes)
        !            46:     are not shown. If Address is specified (X::X), shows the route
        !            47:     that the address matches.
        !            48: 
        !            49:   show ipv6 ospf6 route redistribute (X::X)
        !            50:     Shows the routes advertised as AS-External routes by the router
        !            51:     itself. If Address is specified (X::X), shows the route
        !            52:     that the address matches.
        !            53: 
        !            54: CONFIG NODE:
        !            55:   interface NAME
        !            56:     To enter INTERFACE NODE
        !            57: 
        !            58:   router ospf6 ...
        !            59:     To enter OSPF6 NODE
        !            60: 
        !            61: INTERFACE NODE:
        !            62:   ipv6 ospf6 cost COST
        !            63:     Sets the interface's output cost. default 1
        !            64: 
        !            65:   ipv6 ospf6 hello-interval HELLOINTERVAL
        !            66:     Sets the interface's Hello Interval. default 10
        !            67: 
        !            68:   ipv6 ospf6 dead-interval DEADINTERVAL
        !            69:     Sets the interface's Router Dead Interval. default 40
        !            70: 
        !            71:   ipv6 ospf6 retransmit-interval RETRANSMITINTERVAL
        !            72:     Sets the interface's Rxmt Interval. default 5
        !            73: 
        !            74:   ipv6 ospf6 priority PRIORITY
        !            75:     Sets the interface's Router Priority. default 1
        !            76: 
        !            77:   ipv6 ospf6 transmit-delay TRANSMITDELAY
        !            78:     Sets the interface's Inf-Trans-Delay. default 1
        !            79: 
        !            80: OSPF6 NODE:
        !            81:   router-id A.B.C.D
        !            82:     Sets the router's Router-ID
        !            83: 
        !            84:   interface NAME area AREA
        !            85:     Binds interface to specified Area, and start
        !            86:     sending OSPFv3 packets.
        !            87: 
        !            88: Sample configuration is in ospf6d.conf.sample.
        !            89: 
        !            90: --
        !            91: Yasuhiro Ohara <yasu@sfc.wide.ad.jp>
        !            92: Kunihiro Ishiguro <kunihiro@zebra.org>
        !            93: